32 Commits
Author SHA1 Message Date
rich 26a8387a6e hardware: SB-LoRa rev 2 draft case: a two-part OpenSCAD shell for FDM, the in-slot part from nkorth's CC0 Springboard slot cover, a bump for the radio boards, LiPo and an FPC antenna, split at the board's top face with two M2 screws; the connector height, J1 body and radio/LiPo heights are parameters to measure 2026-11-19 23:09:41 -05:00
rich 1d43beeabf hardware: SB-LoRa rev 2 J1 as a straddle for the MCS-068SMA1: pins 1-34 on F.Cu, 35-68 on B.Cu directly opposite at 1.27 mm (rev 1's split); row position, pad size and board thickness are estimates until a part is measured. Rerouted: DRC 0 unconnected, verify.py checks the straddle and passes; renders regenerated 2026-11-19 22:58:16 -05:00
rich f5653d9d2c docs: SB-LoRa rev 2: show the top and bottom renders in REV2.md, noting they still have the placeholder J1 2026-11-19 22:50:06 -05:00
rich fdacc2daa8 docs: SB-LoRa rev 2 connector: the MCS-068SMA1 straddle parts are ordered (2026-11-19) and J1 is designed around them; no stock of the single-row MCS-068SSA1 turned up 2026-11-19 22:41:33 -05:00
rich f41ddf43bd docs: SB-LoRa rev 2 connector: the MCS-068SMA1 is Robinson Nugent's MEMPAK straddle receptacle (.050" pitch, no tail offset) per the catalogue overview page; the row gap still needs a sample, and the single-row MCS-068SSA1 is noted as a single-sided alternative 2026-11-19 22:39:23 -05:00
rich ef1d245c73 docs: SB-LoRa rev 2 connector: 3M MCS-068SMA1-TR30 (female straddle receptacle, eBay surplus, rows not staggered) replaces the AliExpress part as the J1 candidate, which is dropped for $39 shipping and a 2+ week wait; the J1 pattern becomes opposed F.Cu/B.Cu rows and the board thickness follows the connector's row gap 2026-11-19 22:30:01 -05:00
rich fff912fb4d docs: SB-LoRa rev 2 connector: the J1 listing photo shows an AMP-marked part with no part number but it's sold as Jiansu BST, so the land pattern comes from the parts that arrive and they're bought in one lot 2026-11-19 22:19:53 -05:00
rich e71f979dce docs: SB-LoRa rev 2 connector: the AliExpress 68-pin female PCMCIA part is the J1 candidate (female side, both rows of tails flat on top per the listing photos); its land pattern waits on a measured sample, and the Hirose IC1K listing looks like a host-side socket 2026-11-19 22:18:32 -05:00
rich 0e37755b66 docs: SB-LoRa rev 2 connector: drop the unconfirmed Amphenol 1C1K candidate and list the parts ruled out (out of production, host-side, or a SIM tray), so J1 has no stocked candidate yet 2026-11-19 22:10:04 -05:00
rich ecd9900ec1 hardware: SB-LoRa rev 2 layout: 4 layers (In1 GND plane), flash, UART and logic in the slot, XIAO and Wio side by side, LiPo pads underneath; routed with Freerouting 1.9.0, DRC 0 unconnected, verify.py passes. J1 is a parametric placeholder until a single-sided card-side receptacle is chosen, so it isn't ready to order; the UART footprint becomes NXP's SOT617-1 (EP 3.1 mm), and REV2.md drops TE 5535657, which is the host-side header 2026-11-17 20:35:15 -05:00
rich 6d4cadadbc docs: SB-LoRa temporary connector options for rev 1 now the Hirose IC1HA order is cancelled (harvested straddle, donor connector on wires, top-mounted SMT receptacle, PCMCIA card part), with the 17 pins rev 1 uses; rev 2 drops the straddle footprint 2026-11-17 19:20:57 -05:00
rich 00feaffca5 hardware: SB-LoRa rev 2 footprints for the XIAO (flat or by its header, bottom BAT/SWD pads through solder-filled holes), the Wio (14 holes) and the LiPo pads, generated from Seeed's own KiCad files 2026-11-09 15:17:32 -05:00
rich bbfb334431 hardware: SB-LoRa rev 2 LCSC numbers for the flash (C914935), OR gate (C91874), inverters (C105251) and dual translator (C15741) 2026-11-09 15:12:25 -05:00
rich 440845684c hardware: SB-LoRa rev 2 flash pinout checked against the S29AL016J datasheet; it reads as an Am29LV160BB to Handspring's flash driver 2026-11-09 15:10:31 -05:00
rich de88c7a7a1 hardware: SB-LoRa rev 2 netlist draft: S29AL016J flash on CS0, SC16C650B UART on CS1 with OR-gated strobes (the slot can assert OE*/WE* with CS1*, the UART wants 10 ns after CS), XIAO and Wio side by side, battery and SWD pads. Plan: the flash's installer copies the app to RAM, since the transport's interrupt handler can't live on a removable module; battery sizing estimate 2026-11-09 13:46:56 -05:00
rich f33f5d18dc docs: SB-LoRa rev 2 plan: keep the flash, and replace the SC16IS740 SPI bridge with a 16550-style UART on CS1*, since the flash already needs the full bus 2026-11-09 13:38:47 -05:00
rich 4dd5e5893d docs: SB-LoRa rev 2 plan: how the app gets onto the flash (make rom, an updater .prc run from RAM, Handspring's MakeROM and Flash Manager sources as the base) 2026-11-09 13:37:25 -05:00
rich 99b66a2cf9 docs: SB-LoRa rev 2 plan: running from the module's flash leaves the app's features intact (all data is in RAM databases); note the copy-to-RAM alternative 2026-11-09 13:30:49 -05:00
rich 62d22b59dc docs: SB-LoRa rev 2 plan: the Wio's underside is bare, so it sits flush on the carrier 2026-11-09 13:18:52 -05:00
rich 189091e462 docs: SB-LoRa rev 2 plan: the Wio's 8 mm top socket comes off; it was the tallest part once the XIAO moves alongside 2026-11-09 13:18:21 -05:00
rich 460b82a214 docs: SB-LoRa rev 2 plan: the Wio mounts by its own male pins through the carrier; its unused top socket is the tallest part and may come off 2026-11-09 13:16:56 -05:00
rich 41043065f2 docs: SB-LoRa rev 2 plan: correct the battery cut-out note (rev 1 has none) 2026-11-09 13:15:26 -05:00
rich 14920abb52 docs: SB-LoRa rev 2 plan: reach the XIAO's bottom BAT and SWD pads through solder-filled plated holes in the carrier, so it can sit flat with no gap for battery wires 2026-11-09 13:15:21 -05:00
rich d1be438e63 docs: SB-LoRa rev 2 plan: the XIAO and Wio unplug from each other, so side by side needs only the XIAO's pin header dealt with; drop the stacked fallback 2026-11-09 13:13:08 -05:00
rich 2fc4aa6203 docs: SB-LoRa rev 2 plan: connector change waits on the Hirose order; the XIAO and Wio come soldered together, so side by side means separating them, with a headerless stack as the fallback 2026-11-09 13:11:08 -05:00
rich a4a70fb3eb docs: SB-LoRa rev 2 plan: XIAO and Wio side by side instead of stacked, a CS0 flash so the app loads on insertion, and a single-sided PC Card connector in place of the obsolete Hirose straddle part; lists what's still open 2026-11-09 13:08:29 -05:00
rich bb2fc014ab palm-client: the module can't keep waking a Visor on failing batteries. A slot power handler (SbPwr, in the copied block) stops the chip interrupting on a low-voltage shutdown, as the Springboard guide asks of modules without LOWBAT*; since the Neo's OS never reports that reason, the wake's card event handler and BgArmWake also check the battery and turn the wake off at the OS's warning level. Host-tested; untested on hardware 2026-11-08 19:27:39 -05:00
rich db46a0806f hardware: SB-LoRa bring-up plan (BRINGUP.md): bare-board and bench-power checks, what each SB-LoRa Test line means and what a failure points to (including the A0 mapping and the read values), moving the XIAO stack over, the Slot link, the message wake and standby current 2026-11-08 19:19:33 -05:00
rich 04079afe99 sb-lora: J1 is obsolete; document sourcing and drop unverified XKB substitute
Track the eBay NOS order and open questions about connector offset
variants and long-term supply in progress.md.
2026-11-01 10:08:51 -05:00
rich a9980648bf sb-lora: correct U1-U7 rotations in CPL for JLC part models
Checked in JLC's placement preview: U1, U2, U4 needed a 90 deg clockwise
turn (270) and U3, U5-U7 a 180 deg turn for pin 1 to land on the pin-1
pad. Y1 and D1 were already correct.
2026-10-30 14:23:39 -04:00
rich cf22b6dbde sb-lora: replace out-of-stock crystal with SX3B14.7456F2010F30 (C2901666)
SXT32413BA07 (C6264361) is out of stock at LCSC. Same 14.7456 MHz and
3225-4P footprint; 20 pF load vs 13 pF, so with the existing 22 pF caps
it runs a few tens of ppm high, which is irrelevant for UART timing.
2026-10-30 13:57:15 -04:00
rich b1b2171852 Initial import: SB-LoRa v0.1 hardware, MeshCore UART patch, design docs
Organize the planning-session outputs into hardware/, firmware/,
palm-client/ and docs/, with design notes and a progress tracker.
2026-10-30 13:33:31 -04:00