docs: SB-LoRa temporary connector options for rev 1 now the Hirose IC1HA order is cancelled (harvested straddle, donor connector on wires, top-mounted SMT receptacle, PCMCIA card part), with the 17 pins rev 1 uses; rev 2 drops the straddle footprint

This commit is contained in:
rich committed 2026-11-17 19:20:57 -05:00
1 parent fec5a03358
commit 6d4cadadbc
2 files changed
+23 -3

No files matched your search

+20
View File
@@ -33,6 +33,26 @@ A Springboard module for the Handspring Visor that carries a Seeed XIAO nRF52840
- The Springboard connector core is a standard PCMCIA 68-pin connector with different housing keying (Dev Guide §5, §7.1). Handspring used four board-offset variants (−0.3, 0, +0.3, +0.6 mm); a harvested connector's offset sets how high the board sits in the slot, so compare it against a (51) or dry-fit before soldering.
- An earlier note here suggested XKB X1321FV-2x34 (LCSC C2881777) as a substitute. That was never verified: the closest LCSC listing (X1321FVS-2x34, C2881881) is a vertical SMD socket, not an edge straddle, and won't fit this footprint.
- Pin 1 is marked on silk at the right-hand end of the top row.
- **Without the Hirose part.** The order for one was cancelled (Nov 2026). Rev 1 only uses these Springboard pins, so any receptacle that fits the slot needs about 12 good joints:
| Signal | Pins |
|---|---|
| GND | 1, 34, 35, 68 |
| CD1\*, CD2\* (to GND, or the OS sees no module) | 36, 67 |
| VCC (VSB) | 17, 51 |
| CS0\*, CS1\* | 7, 42 |
| A8, A17 | 12, 46 |
| D0 | 30 |
| IRQ\* | 16 |
| RESET\* | 58 |
VDOCK (18, 52) is only needed if JP1 is bridged. Temporary options, best first:
1. **Harvest a straddle connector** from a junk Springboard module (backup modules, Eyemodule, MiniJam and so on). It fits the footprint as designed; check its board offset against the slot first.
2. **Donor connector on wires.** Cut a junk module's PCB just behind its connector, cut its traces, and wire its pads for the pins above to the matching J1 pads (or vias on the same nets). The donor strip sets the height in the slot; rev 1 sits outside, glued or taped to it.
3. **Single-sided SMT PC Card receptacle** glued to the top at the edge. Top-row tails (1-34) go to the top pads where they line up (staggered tails need short jumpers). The 8 used bottom-row pins (35, 36, 42, 46, 51, 58, 67, 68) are wired around the edge to the bottom pads. The board then sits about 1 mm off the contact centre line, so dry-fit it: the edges may need filing to run in the slot's rails.
4. **Receptacle from a junk PCMCIA card.** Same contacts, but its housing keys may block the Springboard slot, and a straddle part is sized for a thinner card PCB than 1.6 mm. Try it only if one is to hand.
Whichever you use, check continuity from each used pin to its net and do the bench-power checks in [BRINGUP.md](BRINGUP.md) before it goes in the Visor.
2. **J2/J3**: two 1x7 2.54 mm female headers (low-profile if you can find them). Your XIAO+Wio stack plugs in here. You can also solder the stack's pins straight into the holes.
3. **JP1**: leave **open**. See VDOCK below.
+3 -3
View File
@@ -1,6 +1,6 @@
# SB-LoRa rev 2 plan
Draft, nothing designed yet. Rev 1 (`hw-v0.1`) is ordered and shipping, but its Hirose IC1HA straddle connector is obsolete and the order for one may not ship. Rev 2 changes the connector, adds a flash chip so the app loads itself, and makes the module as flat as possible.
Draft, not laid out yet. Rev 1 (`hw-v0.1`) is ordered and shipping, but its Hirose IC1HA straddle connector is obsolete and the order for one was cancelled (2026-11-17). Until rev 2 arrives, rev 1 is built with a harvested or wired-on connector (see "Without the Hirose part" in [README.md](README.md)). Rev 2 changes the connector, adds a flash chip so the app loads itself, and makes the module as flat as possible.
## Decided
@@ -68,7 +68,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc
## Open
- **Connector: waiting on the Hirose IC1HA order.** If it ships, rev 2 keeps rev 1's straddle footprint. If it's cancelled, switch to a single-sided SMT PC Card receptacle (both rows of tails on the top side), harvested or stocked (TE 5535657-2 and Amphenol 1C1K are candidates; check they're the card-side receptacle). The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, tail pitch, row spacing, tail distance from the mating face, and board surface height relative to the contact centre line.
- **Connector: the Hirose IC1HA order was cancelled (2026-11-17)**, so rev 2 drops the straddle footprint for a single-sided SMT PC Card receptacle (both rows of tails on the top side), harvested or stocked (TE 5535657-2 and Amphenol 1C1K are candidates; check they're the card-side receptacle). The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, tail pitch, row spacing, tail distance from the mating face, and board surface height relative to the contact centre line.
- **Case.** The keying is in the module case, so rev 2 needs a case (printed, or a harvested Springboard shell) whose key and latch match the slot, with the board held at the connector's height. Dry-fit a bare harvested connector in the slot to check the contacts seat fully.
- **Board thickness.** The straddle connector forces 1.6 mm; a top-mount one may allow 0.8-1.0 mm.
- **LiPo size.** The aim is at least a few days per charge. Estimate, to be replaced by a measurement:
@@ -81,7 +81,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc
`rev2/netlist.py`, same shape as rev 1's `source/netlist.py` (rev 1 stays as built under `hw-v0.1`). Not laid out yet. Before layout:
- Footprints: `rev2/make_footprints.py` writes `rev2/visormesh.pretty` (XIAO_SMD, WIO_PTH, BAT_PADS) from Seeed's own KiCad files. Open them in KiCad and check against a real XIAO and Wio with calipers before ordering.
- J1 stays rev 1's straddle footprint until the connector order is settled.
- J1 is still rev 1's straddle footprint in the netlist. It's replaced once a single-sided receptacle sample is measured (see Open).
## Carried over from rev 1