docs: SB-LoRa rev 2 connector: the MCS-068SMA1 straddle parts are ordered (2026-11-19) and J1 is designed around them; no stock of the single-row MCS-068SSA1 turned up

This commit is contained in:
rich committed 2026-11-19 22:41:33 -05:00
1 parent f41ddf43bd
commit fdacc2daa8
1 file changed
+2 -2
+2 -2
View File
@@ -68,7 +68,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc
## Open
- **Connector: the Hirose IC1HA order was cancelled (2026-11-17).** Candidate: 3M MCS-068SMA1-TR30, a 68-contact female PCMCIA receptacle for memory cards ("MEMPAK"), straddle mount, sold on eBay as surplus. It's a Robinson Nugent part (later 3M). The only document found is a catalogue overview page (Robinson Nugent PC Card Products p. 330, "MEMPAK Receptacles"), which gives "PCMCIA Spec, .050\" straddle mount, SMT solder tails, Standard mounting ears" with no offset on the tails; its drawing is on catalogue p. 333, which hasn't turned up. So each row is 34 tails at 1.27 mm, and the listing photos show the two rows directly above each other, with no stagger. The gap between the rows (the board thickness) isn't given, so it and the rest of the land pattern have to be measured from a sample. The same page lists MCS-068SSA1-TR30: one row of 68 SMT tails at .025\" (0.635 mm) on one side of the board, top or bottom mounting. That would suit a single-sided board of any thickness, if one can be found. Buy enough for every board in one order. Ruled out: a generic AliExpress 68-pin female part (single-sided, but $39 shipping and over 2 weeks, and its photos show an AMP-marked part while it's sold as "Jiansu BST"), TE 5535657 (the host-side header), Hirose IC1K-68RD-1.27SF(71) (LCSC lists it as "Connector and Ejector", which reads as the host-side socket), Hirose IC1F-68RD-1.27SF and IC9 (obsolete), Amphenol 10014744-007T and 71299-050CALF (out of production), and Amphenol 7111S1615A01LF (a SIM card tray). The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, the gap between the two rows (the board thickness it takes), tail pitch, tail distance from the mating face, tail width and length, and the body size and any pegs.
- **Connector: the Hirose IC1HA order was cancelled (2026-11-17).** Candidate: 3M MCS-068SMA1-TR30, a 68-contact female PCMCIA receptacle for memory cards ("MEMPAK"), straddle mount, sold on eBay as surplus. It's a Robinson Nugent part (later 3M). The only document found is a catalogue overview page (Robinson Nugent PC Card Products p. 330, "MEMPAK Receptacles"), which gives "PCMCIA Spec, .050\" straddle mount, SMT solder tails, Standard mounting ears" with no offset on the tails; its drawing is on catalogue p. 333, which hasn't turned up. So each row is 34 tails at 1.27 mm, and the listing photos show the two rows directly above each other, with no stagger. The gap between the rows (the board thickness) isn't given, so it and the rest of the land pattern have to be measured from a sample. The same page lists MCS-068SSA1-TR30: one row of 68 SMT tails at .025\" (0.635 mm) on one side of the board, top or bottom mounting. That would suit a single-sided board of any thickness, but no stock turned up (only a broker listing for MCS-068SSA1-TR30TP with no quantity). The MCS-068SMA1 parts from eBay were ordered on 2026-11-19, and J1 is designed around them. Buy enough for every board in one order. Ruled out: a generic AliExpress 68-pin female part (single-sided, but $39 shipping and over 2 weeks, and its photos show an AMP-marked part while it's sold as "Jiansu BST"), TE 5535657 (the host-side header), Hirose IC1K-68RD-1.27SF(71) (LCSC lists it as "Connector and Ejector", which reads as the host-side socket), Hirose IC1F-68RD-1.27SF and IC9 (obsolete), Amphenol 10014744-007T and 71299-050CALF (out of production), and Amphenol 7111S1615A01LF (a SIM card tray). The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, the gap between the two rows (the board thickness it takes), tail pitch, tail distance from the mating face, tail width and length, and the body size and any pegs.
- **Case.** The keying is in the module case, so rev 2 needs a case (printed, or a harvested Springboard shell) whose key and latch match the slot, with the board held at the connector's height. Dry-fit a bare harvested connector in the slot to check the contacts seat fully.
- **Board thickness.** A straddle connector sets it: the board is whatever fits between the two rows. The Hirose IC1HA took 1.6 mm, but PC Card internal boards are often about 0.8 mm, so measure the 3M part's gap before assuming 1.6 mm.
- **LiPo size.** The aim is at least a few days per charge. Estimate, to be replaced by a measurement:
@@ -87,7 +87,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc
- **Renders:** `rev2/renders/`.
Before ordering:
1. **J1.** Get samples of the 3M MCS-068SMA1 (above) and measure one with calipers. The straddle needs a new pattern in `build_board.py`: one row of pads on F.Cu and one on B.Cu, directly opposite each other, in place of the current two staggered rows on top. Set the `J1_*` constants from the sample: pitch, each row's distance from the edge, and pad size. Keep the 5.5 mm strip along the edge free (`J1_KEEP`) on both sides, and check whether the connector body needs the board edge moved. Then run `make.sh` and `make_fab.py` again. The current pattern is a placeholder: two staggered rows of 0.5 x 1.6 mm pads on the top, 1.3 and 3.5 mm in from the edge.
1. **J1.** When the MCS-068SMA1 parts arrive (ordered 2026-11-19), measure one with calipers. The straddle needs a new pattern in `build_board.py`: one row of pads on F.Cu and one on B.Cu, directly opposite each other, in place of the current two staggered rows on top. Set the `J1_*` constants from the sample: pitch, each row's distance from the edge, and pad size. Keep the 5.5 mm strip along the edge free (`J1_KEEP`) on both sides, and check whether the connector body needs the board edge moved. Then run `make.sh` and `make_fab.py` again. The current pattern is a placeholder: two staggered rows of 0.5 x 1.6 mm pads on the top, 1.3 and 3.5 mm in from the edge.
2. **XIAO and Wio footprints.** Check them against the real boards with calipers (print the top copper at 1:1).
3. **Assembly.** In JLC's placement preview, check the rotation of U1 (pin 1 at the top left, beside the triangle), U2, U3, U5 and Y1.
4. **Board thickness.** Match it to the 3M part's gap between the rows. If that's thinner than 1.6 mm, change `SetBoardThickness` in `build_board.py` and the thickness in the JLC order to suit.