hardware: SB-LoRa rev 2 LCSC numbers for the flash (C914935), OR gate (C91874), inverters (C105251) and dual translator (C15741)

This commit is contained in:
rich committed 2026-11-09 15:12:25 -05:00
1 parent 440845684c
commit bbfb334431
2 files changed
+8 -9

No files matched your search

+2 -3
View File
@@ -55,10 +55,10 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc
- Part: NXP SC16C650BIBS (32-byte FIFOs, HVQFN32, LCSC C729132). The SC16C750BIBS (64-byte) has the same HVQFN32 pinout and fits the footprint; the SC16C550B doesn't. At 115200 baud a 32-byte FIFO fills in 2.8 ms.
- Wiring:
- Strobes: the slot may assert OE*/WE* at the same moment as CS1* (Dev Guide table 6-2), but the UART wants IOR/IOW 10 ns after its CS. So the UART's CS is tied active and a 74LVC2G32 makes IOR = OE* OR CS1* and IOW = WE* OR CS1*. Nothing else on the bus is affected: the UART only drives the data bus while IOR is low.
- Strobes: the slot may assert OE*/WE* at the same moment as CS1* (Dev Guide table 6-2), but the UART wants IOR/IOW 10 ns after its CS. So the UART's CS is tied active and a SN74LVC2G32 makes IOR = OE* OR CS1* and IOW = WE* OR CS1*. Nothing else on the bus is affected: the UART only drives the data bus while IOR is low.
- Register select A0-A2 of the UART from A1-A3 of the slot, so the registers sit at word addresses.
- UART D0-D7 on slot D0-D7. The driver uses 16-bit reads and writes and keeps the low byte (a 68k byte access at an even address uses D8-D15).
- The UART's INT and RESET are active high and the slot's IRQ* and RESET* are active low, so a 74LVC2G04 inverts both.
- The UART's INT and RESET are active high and the slot's IRQ* and RESET* are active low, so an SN74LVC2G04 inverts both.
- Clock: keep rev 1's 14.7456 MHz crystal (divisor 8 for 115200).
- Wait states: csSlot0 and csSlot1 share one setting, so it's set for the slower of the flash and the UART.
- Powered from the slot (VSB), with the level translators to the XIAO's always-on side as on rev 1.
@@ -79,7 +79,6 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc
## Netlist
`rev2/netlist.py`, same shape as rev 1's `source/netlist.py` (rev 1 stays as built under `hw-v0.1`). Not laid out yet. Before layout:
- Look up LCSC numbers for the flash, 74LVC2G32, 74LVC2G04 and SN74LVC2T45.
- Make footprints for the XIAO (castellated edge plus plated holes under its bottom pads, from Seeed's footprint) and the Wio (14 plated holes).
- J1 stays rev 1's straddle footprint until the connector order is settled.
+6 -6
View File
@@ -26,13 +26,13 @@ Pin tables that still need checking against a datasheet are marked VERIFY.
PARTS = {
"J1": ("Springboard 68p straddle", None, "SPRINGBOARD_68", "",
"Hirose IC1HA-68RD-1.27SH(51); pending the order (REV2.md). Hand-solder", True),
"U1": ("S29AL016J70TFI020", "Package_SO", "TSOP-I-48_18.4x12mm_P0.5mm", "",
"U1": ("S29AL016J70TFI020", "Package_SO", "TSOP-I-48_18.4x12mm_P0.5mm", "C914935",
"2 MB NOR flash, x16, 70 ns, csSlot0", False),
"U2": ("SC16C650BIBS", "Package_DFN_QFN", "HVQFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm", "C729132",
"UART, 32-byte FIFOs, csSlot1 (SC16C750BIBS fits the same footprint)", False),
"U3": ("74LVC2G32DC", "Package_SO", "VSSOP-8_2.3x2mm_P0.5mm", "", "OR: UART read/write strobes", False),
"U4": ("74LVC2G04GW", "Package_TO_SOT_SMD", "SOT-363_SC-70-6", "", "Inverters: INT -> IRQ*, RESET* -> RESET", False),
"U5": ("SN74LVC2T45DCUR", "Package_SO", "VSSOP-8_2.3x2mm_P0.5mm", "",
"U3": ("SN74LVC2G32DCUR", "Package_SO", "VSSOP-8_2.3x2mm_P0.5mm", "C91874", "OR: UART read/write strobes", False),
"U4": ("SN74LVC2G04DCKR", "Package_TO_SOT_SMD", "SOT-363_SC-70-6", "C105251", "Inverters: INT -> IRQ*, RESET* -> RESET", False),
"U5": ("SN74LVC2T45DCUR", "Package_SO", "VSSOP-8_2.3x2mm_P0.5mm", "C15741",
"Ioff xlate: UART TX -> XIAO D7, Visor-present -> XIAO D0", False),
"U6": ("SN74LVC1T45DCKR", "Package_TO_SOT_SMD", "SOT-363_SC-70-6", "C9382", "Ioff xlate: XIAO D6 -> UART RX", False),
"Y1": ("14.7456MHz 20pF", "Crystal", "Crystal_SMD_3225-4Pin_3.2x2.5mm", "C2901666", "SX3B14.7456F2010F30", False),
@@ -128,11 +128,11 @@ for pad, net in {1: "D5", 2: "D6", 3: "D7", 4: "UART_BAUD", 5: "UART_RX", 6: "UA
# Y1 3225 4-pad: 1/3 crystal, 2/4 case
c("Y1", 1, "XTAL1"); c("Y1", 3, "XTAL2"); c("Y1", 2, "GND"); c("Y1", 4, "GND")
c("C6", 1, "XTAL1"); c("C6", 2, "GND"); c("C7", 1, "XTAL2"); c("C7", 2, "GND")
# U3 74LVC2G32 (8-pin): 1 1A, 2 1B, 3 2Y, 4 GND, 5 2A, 6 2B, 7 1Y, 8 VCC
# U3 SN74LVC2G32 (VSSOP-8): 1 1A, 2 1B, 3 2Y, 4 GND, 5 2A, 6 2B, 7 1Y, 8 VCC
for pad, net in {1: "OE_N", 2: "CS1_N", 7: "UART_IOR_N", 5: "WE_N", 6: "CS1_N", 3: "UART_IOW_N",
4: "GND", 8: "VSB"}.items():
c("U3", pad, net)
# U4 74LVC2G04 (SC-70-6): 1 1A, 2 GND, 3 2A, 4 2Y, 5 VCC, 6 1Y
# U4 SN74LVC2G04 (SC-70-6): 1 1A, 2 GND, 3 2A, 4 2Y, 5 VCC, 6 1Y
for pad, net in {1: "UART_INT", 6: "IRQ_N", 3: "RESET_N", 4: "UART_RESET", 2: "GND", 5: "VSB"}.items():
c("U4", pad, net)
# U5 SN74LVC2T45 (VSSOP-8): 1 VCCA, 2 A1, 3 A2, 4 GND, 5 DIR, 6 B2, 7 B1, 8 VCCB. DIR high = A->B