The `recv_pkt_region` is set when processing a flood packet in `filterRecvFloodPacket`
but direct/non-flood packets would never pass through that function, so the pointer was
not cleared for them.
`sendFloodReply` would then later use it blindly, which meant that the response would
either inherit the region from the last flood packet, or refer to a non-initialised pointer
if no region floods had been received yet.
If an `ota pull <#> folder` block-write fails mid-transfer (the motatool seeder
link dropped), the fetch enters a new PAUSED state instead of failing or falling
back to RAM/flash: progress stays on the host, the manager stops requesting, and
loop()/stall-detection leave it untouched (it waits indefinitely). On reconnect
the ESP32 seeder re-registers the folder destination and, if PAUSED, calls
resumeStaged(): OP_STAT re-attaches the host's partial, the leaves are re-read,
and only the missing blocks are re-requested (a brand-new/absent file restarts
from 0). `ota status` reports the paused state.
FolderMotaStore: an OtaStore that streams an in-transit .mota straight to the host
folder over the seeder link (OP_BEGIN/WRITE/SREAD/STAT/FIN) instead of RAM/flash —
the device holds no local staging for it. Wired as a selectable pull destination:
- OtaContext gains a folder_dest (registered by the app while a motatool `serve`
link is up) + its human id (e.g. "tcp 192.168.4.5").
- `ota pull <#> <dest>` now takes a MANDATORY destination; `ota pull <#>` with none
lists the choices (flash always; folder + its link id when connected).
- The ESP32 WiFi seeder registers/clears the folder destination on connect/close —
the same connection both serves the folder and accepts pulls into it.
Captures an exact copy of a device's firmware over the mesh to build a delta
against. Pause/resume on a mid-pull disconnect follows.
The discovery beacon previously re-announced at a random 3-10 min interval.
Replace that with a fixed, user-configurable cadence:
- OtaManager::advert_mins() — re-advertise every N minutes after the boot
burst; 0 disables periodic re-advertise (boot burst only). Default 24h.
- Persisted in NodePrefs (CommonCLI) and runtime-tunable: `ota config advert
<minutes>` (0..10080; 0 = off), and shown in `ota config`.
- When periodic advert is disabled, the scheduler still re-checks the config
on a slow timer, so a later `ota config advert <mins>` takes effect live.
Also advertise immediately whenever the served set changes — when a motatool
folder is attached to / detached from the ESP32 WiFi seeder — so peers learn
about newly-available firmware without waiting for the next interval (the
`ota folder` serial path already announced on attach).
Docs: protocol beacon-cadence note + user-guide `ota config advert`.
Extends the USB-serial folder relay to WiFi so an ESP32 companion can both
serve .mota and be operated headlessly:
- motatool `serve --tcp <host[:port]>`: a TcpTransport sibling of the serial
transport (default port 5001). SeederCore/Folder are reused unchanged — the
COUNT/DESCRIBE/READ protocol is transport-agnostic.
- ESP32 companion: a dedicated OTA seeder port (5001) for `serve --tcp`, plus
an OTA text console on 5002 (`nc <ip> 5002` -> `ota status|ls|announce|...`,
the same handle_ota_command CLI serial nodes have). Both run alongside the
phone-app port (5000); all three coexist.
- WiFi.setSleep(false): ESP32 STA mode's modem power-save periodically sleeps
the modem/CPU and stalls the SX1262 SPI+DIO servicing, leaving LoRa deaf
while WiFi is associated. Disabling it restores the radio (HW-validated:
a V3 WiFi companion is then discovered over LoRa and discovers its peers).
- docs: serving .mota over WiFi (protocol §10.2 + user guide).
Refactored the handling of observer-related settings by moving them from
NodePrefs to a new MQTTPrefs structure. This change centralizes MQTT,
WiFi, timezone, SNMP, and alert configurations, improving code organization
and maintainability. The new structure allows for better separation of
concerns and prepares the codebase for future enhancements.
Implemented new commands for configuring and diagnosing NTP server
settings in the MQTT bridge. Users can now set a custom NTP server
and probe connectivity to configured servers. This enhancement
improves time synchronization reliability for JWT authentication
and provides better diagnostics for NTP connectivity issues.
Implemented functionality to generate and compare partition-table
signatures during OTA updates. This enhancement ensures that the
target build's partition layout matches the device's actual layout,
improving the reliability of OTA updates and preventing issues
related to partition changes.
Enhanced the firmware versioning system by appending a build number
suffix when available, allowing for better tracking of published builds.
This change improves the OTA update process by providing clearer
versioning information in the embedded firmware string.
Added support for deferred OTA updates in the MyMesh class, allowing
the system to schedule firmware updates to occur after a confirmation
reply is sent. This change improves the user experience by ensuring
that the update process does not block the main application loop,
allowing for smoother operation during firmware updates.