The back panel may need a filed cutout and a snipped grille to close over the Lyra and its Wi-Fi lead
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
This commit is contained in:
1 parent
2725215484
commit
18517f88db
1 file changed
+13
-1
+13
-1
@@ -82,7 +82,8 @@ a radio in the meantime.
|
||||
| 2.5 mm hex key | Comes with the PicoCalc kit. |
|
||||
| USB-C data cable | For the serial console, and later for flashing the XIAO. A charge-only cable won't do; it has to carry data. |
|
||||
| microSD card reader | For writing the Calculinux image from your PC. |
|
||||
| Small side cutters | For trimming wire ends. |
|
||||
| Small side cutters | For trimming wire ends, and a section of the case grille if the Wi-Fi lead needs the room. |
|
||||
| Small needle file | To open the back panel's USB-C cutout a little if the Lyra's connector doesn't clear it. |
|
||||
| Kapton (polyimide) tape | Wraps the XIAO stack and the DIY USB lead so nothing bare touches the board or the shell. Heat-proof, thin, and it peels off cleanly. |
|
||||
| A PC (Windows/macOS/Linux) with Python 3 and git | Runs the image-writing, firmware-build and flashing steps. |
|
||||
|
||||
@@ -246,6 +247,11 @@ screwed down.
|
||||
You should see the Lyra sitting flat on the socket with no gap at either end, and, once
|
||||
the mainboard is back in, its USB-C port centred in the back-panel cutout.
|
||||
|
||||
The cutout was made for the Pico's micro-USB, and the Lyra's USB-C connector is a
|
||||
different shape. Depending on the connector Luckfox fitted to your board, the back panel
|
||||
may not close over it. If it catches, open the hole a little with a small needle file,
|
||||
testing the fit as you go, until the panel sits down without pressing on the board.
|
||||
|
||||
Leave the back off for now. The microSD card goes into the **Lyra's own slot** in
|
||||
[Step 4](#step-4--write-the-image-to-the-microsd), and that slot is easier to reach with the
|
||||
board exposed.
|
||||
@@ -281,6 +287,12 @@ MX1.25 end into the socket on the Lyra — it is keyed and only goes in one way
|
||||
Wi-Fi dongle into the USB-A end. Lead and dongle stay inside the shell; tuck them where
|
||||
they don't press on the board.
|
||||
|
||||
The MX1.25 socket sits on top of the Lyra, and the lead leaves it upward, which is where
|
||||
the back panel's grille is. The wire may interfere with the grille when the back goes on.
|
||||
If it does, snip a small section out of the grille with the side cutters where the wire
|
||||
passes and shape the edge until nothing presses on the plug or the wire. Better to remove a
|
||||
sliver of plastic than to close the case against a connector.
|
||||
|
||||
> **The Lyra's USB port is 3.3 V, not 5 V.** A standard 5 V USB Wi-Fi dongle will not work
|
||||
> and may damage the board. Stick to the tested chipsets — RTL8192CU, R8712U, or RTL8188EU
|
||||
> — which is why the shopping list names a known dongle (the TP-Link TL-WN725N) and
|
||||
|
||||
Reference in new issue
Block a user