Adapt upstream MeshCore #3579 at 7457cff43c22697119e06ad7d192a37de0990403:
retain GC1109 LF standby bias, with checked cold controls before band supply
changes and shutdown. Preserve exclusive LF/HF rails and TX error cleanup.
Reset before boot rail changes and before SPI-dependent hard recovery.
Retain our stronger implementation of #3512 at
d208bfef94ab83280de30ba4a0675ff73b3ecef3. Add regressions for suspect FIFO
contents, failed RX_DONE acknowledgement, and fresh preamble timing.
W12 TX power defaults from #3319 were already included via 65aa1138a.
Validation: 79 targeted native tests; canonical W12 Full repeater and Full
Companion builds, capability checks, app-size and RAM checks passed.
Physical W12 RF envelope, current and LoRa management confirmation remain.
Upstream PRs:
https://github.com/meshcore-dev/MeshCore/pull/3579
https://github.com/meshcore-dev/MeshCore/pull/3512
https://github.com/meshcore-dev/MeshCore/pull/3319
97 lines
3.4 KiB
C++
97 lines
3.4 KiB
C++
#include <Arduino.h>
|
|
#include "target.h"
|
|
#include <helpers/radiolib/TunableRadioHal.h>
|
|
|
|
MeshnologyW12Board board;
|
|
|
|
#if defined(P_LORA_SCLK)
|
|
static SPIClass spi;
|
|
static TunableRadioHal radio_hal(spi, 2000000);
|
|
RADIO_CLASS radio = new Module(&radio_hal, P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY);
|
|
#else
|
|
static TunableRadioHal radio_hal(SPI, 2000000, true);
|
|
RADIO_CLASS radio = new Module(&radio_hal, P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY);
|
|
#endif
|
|
|
|
WRAPPER_CLASS radio_driver(radio, board);
|
|
|
|
ESP32RTCClock fallback_clock;
|
|
AutoDiscoverRTCClock rtc_clock(fallback_clock);
|
|
|
|
#if ENV_INCLUDE_GPS
|
|
#include <helpers/sensors/MicroNMEALocationProvider.h>
|
|
MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1, &rtc_clock);
|
|
EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea);
|
|
#else
|
|
EnvironmentSensorManager sensors;
|
|
#endif
|
|
|
|
#ifdef DISPLAY_CLASS
|
|
DISPLAY_CLASS display(NULL);
|
|
MomentaryButton user_btn(PIN_USER_BTN, 1000, true);
|
|
#endif
|
|
|
|
const uint32_t rfswitch_dios[] = {
|
|
RADIOLIB_LR2021_DIO5, // RFX2402E 2.4G_TX_EN
|
|
RADIOLIB_LR2021_DIO6, // RFX2402E 2.4G_RX_EN
|
|
RADIOLIB_LR2021_DIO9, // GC1109 CTX (Transmit mode)
|
|
RADIOLIB_LR2021_DIO10, // GC1109 CPS (Bypass mode)
|
|
RADIOLIB_LR2021_DIO11, // GC1109 CSD (Shutdown)
|
|
};
|
|
|
|
static const Module::RfSwitchMode_t rfswitch_table[] = {
|
|
// DIO5 DIO6 DIO9 DIO10 DIO11
|
|
// PR #3579 (7457cff): retain LF PA bias between packets to avoid a weak
|
|
// packet opening. This table is selected only while the LF rail is powered.
|
|
{ LR2021::MODE_STBY, { LOW, LOW, HIGH, HIGH, HIGH } }, // GC1109 stays awake
|
|
{ LR2021::MODE_RX, { LOW, LOW, LOW, HIGH, HIGH } }, // rx_lf: GC1109 LNA (CPS is don't-care in RX)
|
|
{ LR2021::MODE_TX, { LOW, LOW, HIGH, HIGH, HIGH } }, // tx_lf: GC1109 full PA
|
|
{ LR2021::MODE_RX_HF, { LOW, HIGH, LOW, LOW, LOW } }, // rx_hf: 2G4 LNA, GC1109 off
|
|
{ LR2021::MODE_TX_HF, { HIGH, LOW, LOW, LOW, LOW } }, // tx_hf: 2G4 PA, GC1109 off
|
|
END_OF_MODE_TABLE,
|
|
};
|
|
|
|
// Keep both FEMs' controls low in standby while switching supplies or using
|
|
// the HF rail. GC1109 control voltage must not exceed its switched VBAT.
|
|
static const Module::RfSwitchMode_t rfswitch_table_cold[] = {
|
|
{ LR2021::MODE_STBY, { LOW, LOW, LOW, LOW, LOW } },
|
|
rfswitch_table[1],
|
|
rfswitch_table[2],
|
|
rfswitch_table[3],
|
|
rfswitch_table[4],
|
|
END_OF_MODE_TABLE,
|
|
};
|
|
|
|
static bool set_w12_rf_switch_standby(bool lf_awake, bool sleep_after) {
|
|
if (radio.replaceRfSwitchTable(rfswitch_dios,
|
|
lf_awake ? rfswitch_table : rfswitch_table_cold) != RADIOLIB_ERR_NONE) return false;
|
|
return !sleep_after || radio.sleep() == RADIOLIB_ERR_NONE;
|
|
}
|
|
|
|
bool radio_init() {
|
|
fallback_clock.begin();
|
|
rtc_clock.begin(Wire);
|
|
|
|
#if defined(P_LORA_SCLK)
|
|
int err = radio.std_init(&spi);
|
|
if (err != 1) return err;
|
|
#else
|
|
int err = radio.std_init();
|
|
if (err != 1) return err;
|
|
#endif
|
|
|
|
#ifdef RF_SWITCH_TABLE
|
|
// The callback is installed only after initialization: board.begin() may
|
|
// select its first supply before the radio is ready to accept SPI commands.
|
|
board.setRadioRfSwitchHandler(set_w12_rf_switch_standby);
|
|
if (!set_w12_rf_switch_standby(!mesh::lr2021::isHighBand(radio.getFreqMHz()), false)) return false;
|
|
#endif
|
|
|
|
return true;
|
|
}
|
|
|
|
mesh::LocalIdentity radio_new_identity() {
|
|
RadioNoiseListener rng(radio);
|
|
return mesh::LocalIdentity(&rng); // create new random identity
|
|
}
|