Reserve board-specific GPIOs, make ESP-NOW channel/format handling configurable, and coordinate WiFi, BLE, NTP, MQTT, and host actions safely.
Add the Indicator message page, exclusive transport selector, dynamic 480/320 rendering, larger transport typography, pairing cleanup, and corresponding tests and documentation.
* Add tz_offset companion prefs and get/set commands for companion cli
* Use tz_offset for clock on display
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Add durable TempRadio, ACL, clock, bridge, GPS/I2C, USB logging, and Indicator recovery safeguards together with expanded automation, build/profile contracts, release metadata, and the hardware validation ledger.
Add selectable shared ESP-NOW channels, raw/wrapped bridge compatibility, and bounded fragmentation for maximum-size packets.\n\nGive ESP32 Full profiles WiFi coexistence, stabilize WebConfig and USB terminal lifecycles, and keep disabled bridges stopped during observer updates.\n\nUpdate generated UI, firmware selection, documentation, and regression coverage.
Adds both settings to docs/cli_commands.md in the existing format, and records
the R8 dashboard, display controls and the two hardware fixes in the changelog.
The display.flip entry calls out that it is persisted config which survives a
firmware update, since a node still carrying flip=1 from testing looks exactly
like a firmware whose orientation was never fixed.
display.flip lives in /mqtt.json, so it survives a reflash and is invisible
while someone is chasing a wrong orientation - a node still carrying flip=1
from testing looks exactly like a firmware that was never fixed. Boot now
reports "Display: flip off" or "flip on (rotated 180)".
Rotation 2 was consistently upside down on the Expansion Kit V2 panel, so 0
becomes the compiled default for both portrait observer targets.
display.flip is unchanged and still defaults to off: the compiled constant
should be the correct orientation, with the setting reserved for a board
mounted the other way up. A node already carrying `display.flip 1` from
testing needs `set display.flip 0` after this.
Landscape targets are untouched - they take the driver's own DISPLAY_ROTATION
default of 3.
Power-off now needs a 3 second hold; any shorter press toggles the display.
MomentaryButton reports a CLICK for any release short of its threshold, so
that single value defines both.
The button also felt unreliable - "a brief press doesn't wake it, more often
than not". MomentaryButton's multi-click detection withholds a CLICK for
MULTI_CLICK_WINDOW_MS (280 ms) after release, and folds a second press
arriving inside that window into a DOUBLE_CLICK. Since the handler only acts
on CLICK, an impatient second press produced nothing at all: press, see
nothing, press again, still nothing. Multi-click is now off for these targets,
so CLICK fires on release.
Both settings are build flags defaulted in variants/heltec_v4_r8/target.cpp
and overridden only on the two TFT observer bases, because the companion
builds share this user_btn and do use double/triple click.
DISPLAY_TOUCH_DEBUG additionally logs which input caused a toggle
("Display: button -> on"), so any remaining flake can be attributed to the
button or to a spurious touch read rather than guessed at.
Addresses a Codex review of the preceding three commits.
Touch could disable itself for the whole session. begin() latched _present
from a single address probe, but this controller NACKs whenever it has nothing
to report, so an idle probe at boot was indistinguishable from absent
hardware. The probe is now diagnostics only; checkTap() polls regardless, and
a NACK costs one quiet bus cycle.
Touch no longer mutates shared bus state. Wrapping the read in
setTimeOut()/restore was an unsynchronised global write, and the MQTT task
drives the same Wire through AutoDiscoverRTCClock in its NTP fallback, so it
could inherit the short timeout. The address probe alone removes the
ESP_ERR_TIMEOUT stalls that motivated it, and it also ran before the timeout
was installed, so the transaction most exposed to a wedged bus was unprotected
anyway.
A single failed read could fake a release. The debounce window was 40 ms
against a 50 ms poll, so a state change was confirmed by the very next sample
and one NACK mid-touch produced a release followed by a second tap. It is now
80 ms - two consecutive consistent reads.
RadioActivityWindow froze after a gap longer than ~24.8 days. tick() treated
any delta past the signed halfway mark as an out-of-order timestamp, so a node
left unserviced that long kept a month-old packet in the 20-minute window and
reported it as recently received. A backwards step is now only believed when
it is small, which is what an out-of-order reading between two call sites
actually looks like.
Not changed: a downgrade that then saves prefs drops the display group, since
/mqtt.json is rewritten from the older serializer's known schema. That is
inherent to every appended field in this format, and bumping the JSON version
would be worse - older firmware would reject the file rather than ignore one
group. Documented instead.
`set display.flip 0|1` (also off/on) turns the panel 180 degrees from its
compiled DISPLAY_ROTATION, persisted in MQTTPrefs alongside display.timeout
and applied live without a reboot.
Adding 2 to the compiled rotation rather than setting an absolute value keeps
portrait portrait and landscape landscape, so the DisplayViewport geometry
never changes with it and the setting cannot produce a nonsensical mix.
DisplayDriver gains a defaulted no-op setFlipped(), so no other display
driver is affected.
The compiled rotation was verified identical across `pio run` and `build.sh`
on two machines (movi a11, 2 at the setRotation call site), yet the panel read
upside down for one tester and upright for another - which is what a board
mounted either way up looks like. No single compiled constant satisfies both,
so orientation becomes a setting rather than another rebuild.
Runtime-only, like display_timeout_secs: LegacyV1MQTTPrefs and the frozen
binary payload sizes are untouched, and the JSON group is an append that older
firmware skips.
Four defects found by hardware testing of the Expansion Kit V2.
Touch never registered. The panel's controller does not use the point-count
encoding the reference CHSC6X drivers document: byte 0 reads 0x00 idle and
0x1F while a finger is down, so testing for a count of 1 never fired. A
partly-failed read leaves 0xFF, which must not count as a press either, so
the test is now != 0x00 && != 0xFF.
Touch polling could stall the UI loop for ~1 s at a time. The controller
NACKs its address whenever it has nothing to report, and calling requestFrom()
unconditionally logged a bus error on every 50 ms poll and, once the bus
wedged, burned a full ESP_ERR_TIMEOUT inside loop(). Probe the address first,
which reports the same NACK quietly, and bound the read with setTimeOut().
The display could not be woken once it blanked; only RST brought it back.
turnOn() re-ran the whole display.init(), which re-enters SPI setup, spends
~500 ms in Adafruit's reset delays and pulses GPIO 21 - the line shared with
TP_RST, so it reset the touch controller on every wake. Since turnOff() no
longer parks that line low, the panel stays configured while dark and waking
is just the backlight. Toggling also clears the refresh deadline so the
current frame is drawn immediately instead of the stale one.
Power-off rebooted instead of staying off. powerOff() went through
enterDeepSleep(), which always arms an ext1 wake on P_LORA_DIO_1; a deep-sleep
wake is a full reboot, so a node in live traffic restarted within seconds of
showing "Turning OFF". It now disables every wake source, so the node stays
down until RST or a power cycle.
Note that the display off/on cycle had never been exercised on this board
before: observer builds pinned AUTO_OFF_MILLIS=0, so the panel never blanked
until display.timeout made it a runtime setting.
Replace the sparse Heltec V4 R8 observer home screen with a padded dark
analytics dashboard, add manual display control, and make blanking a runtime
setting.
Dashboard (DISPLAY_ACTIVITY_DASHBOARD, the four R8 TFT observer envs):
- RadioActivityWindow: 20 one-minute buckets of valid RX packets, no heap.
The caller's 32-bit millis() is extended to a monotonic 64-bit clock, so
nothing downstream has a rollover case; an always-on node passes 2^32 ms
after ~49.7 days, which would otherwise re-enter warm-up and divide 20
minutes of traffic by seconds. Rates use 19 whole minutes plus the elapsed
part of the current one rather than a fixed 1200 s.
- ObserverDashboard: header, radio strip, headline totals, a 20-bar
packets-per-minute graph and RF/status footers, with separate portrait and
landscape layouts. A text row is a fixed 16 px, which is 3.2 logical units
in portrait but 4.27 in landscape, so one shared grid would overlap.
Text is trimmed by character budget, not measured width: getTextWidth()
reports an over-long string at the portrait driver's fallback scale, so
DisplayDriver::drawTextEllipsized() under-trims and the row renders at half
height.
- Six per-row signatures computed from what is actually drawn, so only the
rows whose pixels changed repaint. No startFrame(), no whole-screen clear.
Link state moved out of the full-frame signature, so a DHCP renewal or WiFi
flap repaints one footer row instead of the panel.
- Dark theme by retuning the UIColor statics at runtime, which needs no
display-driver edit and carries boot, setup, reboot and power-off with it.
Touch and button (DISPLAY_TOUCH_TOGGLE):
- CHSC6X at I2C 0x2E, polled; TP_INT is unusable (optional R13, and GPIO 43
is U0TXD). The point-count byte is tested against a valid count, never
against non-zero: an idle read returns 0xFF, which reads as a finger held
down forever and latches the tap detector after one event.
- turnOff() no longer parks PIN_TFT_RST low on this board. GPIO 21 is a
shared LCD_RST/TP_RST net, so doing that held the touch controller in
reset for as long as the display was off. Verified against Heltec's
expansion-board and mainboard schematics and the V4-R8 datasheet pinout,
which also correct the pin comment in HeltecV4R8Board.cpp.
- The USER button click now toggles the display too; it previously did
nothing whenever the display was already on.
display.timeout:
- `set display.timeout <secs>` / `get display.timeout`, 0 = stay on, 60 s
default, 3600 max. Read live, so a change applies without a reboot and
restarts the countdown rather than firing on the old deadline.
- Stored in MQTTPrefs (/mqtt.json), keeping NodePrefs aligned with upstream.
Runtime-only: LegacyV1MQTTPrefs and the four frozen binary payload sizes
are unchanged. No JSON format-version bump - the loader skips keys no
def() claims, so older firmware reads newer files and this firmware reads
older ones with the default applied. Both directions are covered by tests.
- Joins the observer atomic-setter contract, so a failed save rolls the live
value back instead of only claiming to.
New periodic work uses a wrap-safe deadline check; `millis() >= deadline`
fires every loop for a whole interval before each rollover.
Adds test_radio_activity_window, test_observer_dashboard (driving the real
renderer against a recording DisplayDriver in both orientation profiles) and
test_touch_tap_detector. 440 native cases pass.
mikecarper
Kevin Le
Aleksei Mamlin
fdlamotte
taco
Adam Gessaman