Remove Cascadia power saving default

build.sh

@@ -446,7 +446,6 @@ prompt_for_cascadia_profile_enable() {
   echo "  - multi.acks: 1"
   echo "  - path.hash.mode: 2"
   echo "  - loop.detect: minimal"
-  echo "  - powersaving: on"
   prompt_on_off_choice "Enable Cascadia profile overrides" "on"
   if [ "$MENU_CHOICE" == "on" ]; then
     FIRMWARE_PROFILE_OVERRIDE="cascadia"
@@ -958,7 +957,7 @@ apply_radio_overrides() {
 apply_firmware_profile_overrides() {
   case "${FIRMWARE_PROFILE_OVERRIDE,,}" in
     cascadia)
-      export PLATFORMIO_BUILD_FLAGS="${PLATFORMIO_BUILD_FLAGS} -DCASCADIA_PROFILE=1 -DDEFAULT_RX_DELAY_BASE=1.0f -DDEFAULT_LOOP_DETECT=1 -DDEFAULT_POWERSAVING_ENABLED=1 -DDEFAULT_AGC_RESET_INTERVAL=2 -DDEFAULT_ADVERT_INTERVAL=0 -DDEFAULT_FLOOD_ADVERT_INTERVAL=83 -DDEFAULT_MULTI_ACKS=1 -DDEFAULT_PATH_HASH_MODE=2"
+      export PLATFORMIO_BUILD_FLAGS="${PLATFORMIO_BUILD_FLAGS} -DCASCADIA_PROFILE=1 -DDEFAULT_RX_DELAY_BASE=1.0f -DDEFAULT_LOOP_DETECT=1 -DDEFAULT_AGC_RESET_INTERVAL=2 -DDEFAULT_ADVERT_INTERVAL=0 -DDEFAULT_FLOOD_ADVERT_INTERVAL=83 -DDEFAULT_MULTI_ACKS=1 -DDEFAULT_PATH_HASH_MODE=2"
       ;;
   esac
 }

docs/cli_commands.md

@@ -498,7 +498,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 - `on`: enable power saving
 - `off`: disable power saving
 
-**Default:** `on`
+**Default:** `off`
 
 **Note:** When enabled, device enters sleep mode between radio transmissions
 

examples/simple_repeater/MyMesh.cpp

@@ -2143,7 +2143,6 @@ void MyMesh::begin(FILESYSTEM *fs) {
   _prefs.multi_acks = DEFAULT_MULTI_ACKS;
   _prefs.path_hash_mode = DEFAULT_PATH_HASH_MODE;
   _prefs.loop_detect = DEFAULT_LOOP_DETECT;
-  _prefs.powersaving_enabled = DEFAULT_POWERSAVING_ENABLED;
 #endif
   acl.load(_fs, self_id);
   // TODO: key_store.begin();
@@ -2208,6 +2207,34 @@ void MyMesh::sendFloodScoped(const TransportKey& scope, mesh::Packet* pkt, uint3
   }
 }
 
+void MyMesh::sendFloodScopedWithSelfPath(const TransportKey& scope, mesh::Packet* pkt,
+                                         uint32_t delay_millis, uint8_t path_hash_size) {
+  if (pkt == NULL) {
+    return;
+  }
+  if (path_hash_size == 0 || path_hash_size > MAX_ROUTE_HASH_BYTES) {
+    MESH_DEBUG_PRINTLN("%s MyMesh::sendFloodScopedWithSelfPath(): invalid path_hash_size", getLogDateTime());
+    return;
+  }
+
+  pkt->header &= ~PH_ROUTE_MASK;
+  if (scope.isNull()) {
+    pkt->header |= ROUTE_TYPE_FLOOD;
+  } else {
+    uint16_t codes[2];
+    codes[0] = scope.calcTransportCode(pkt);
+    codes[1] = 0;
+    pkt->header |= ROUTE_TYPE_TRANSPORT_FLOOD;
+    pkt->transport_codes[0] = codes[0];
+    pkt->transport_codes[1] = codes[1];
+  }
+
+  pkt->setPathHashSizeAndCount(path_hash_size, 1);
+  self_id.copyHashTo(pkt->path, path_hash_size);
+  getTables()->markSent(pkt);
+  sendPacket(pkt, 1, delay_millis);
+}
+
 bool MyMesh::sendRepeatersFloodText(const char* text) {
   if (text == NULL || *text == 0) return false;
 
@@ -2223,8 +2250,15 @@ bool MyMesh::sendRepeatersFloodText(const char* text) {
 
   const size_t max_data_len = MAX_PACKET_PAYLOAD - CIPHER_BLOCK_SIZE;
   const size_t prefix_cap = max_data_len > 5 ? max_data_len - 5 + 1 : 0;
+  char sender_name[sizeof(_prefs.node_name)];
+  StrHelper::strncpy(sender_name, _prefs.node_name, sizeof(sender_name));
+  for (char* p = sender_name; *p; p++) {
+    if (*p == ':') {
+      *p = ';';
+    }
+  }
   int prefix_written = prefix_cap > 0
-      ? snprintf((char*)&temp[5], prefix_cap, "%s: ", _prefs.node_name)
+      ? snprintf((char*)&temp[5], prefix_cap, "%s: ", sender_name)
       : -1;
   if (prefix_written < 0) {
     return false;
@@ -2247,7 +2281,7 @@ bool MyMesh::sendRepeatersFloodText(const char* text) {
     return false;
   }
 
-  sendFloodScoped(default_scope, pkt, 0, _prefs.path_hash_mode + 1);
+  sendFloodScopedWithSelfPath(default_scope, pkt, 0, _prefs.path_hash_mode + 1);
   return true;
 }
 

examples/simple_repeater/MyMesh.h

@@ -242,6 +242,8 @@ protected:
                              const uint8_t* path, uint8_t path_len,
                              const uint8_t* alt_path, uint8_t alt_path_len,
                              uint32_t delay_millis);
+  void sendFloodScopedWithSelfPath(const TransportKey& scope, mesh::Packet* pkt,
+                                   uint32_t delay_millis, uint8_t path_hash_size);
 
 public:
   MyMesh(mesh::MainBoard& board, mesh::Radio& radio, mesh::MillisecondClock& ms, mesh::RNG& rng, mesh::RTCClock& rtc, mesh::MeshTables& tables);

src/helpers/ESP32Board.h

@@ -73,6 +73,13 @@ public:
       return;
     }
 
+  #if defined(ARDUINO_USB_CDC_ON_BOOT) && ARDUINO_USB_CDC_ON_BOOT
+    if (Serial) {
+      delay(1);
+      return;
+    }
+  #endif
+
     // Set GPIO wakeup
     gpio_num_t wakeupPin = (gpio_num_t)getIRQGpio();