diff --git a/hardware/sb-lora/REV2.md b/hardware/sb-lora/REV2.md index 67fd0d2..e5a4b60 100644 --- a/hardware/sb-lora/REV2.md +++ b/hardware/sb-lora/REV2.md @@ -68,7 +68,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc ## Open -- **Connector: the Hirose IC1HA order was cancelled (2026-11-17).** Candidate: 3M MCS-068SMA1-TR30, a 68-contact female PCMCIA receptacle for memory cards ("MEMPAK"), straddle mount, sold on eBay as 3M/Robinson Helicopter surplus, so probably genuine new-old-stock. The listing photos show the top and bottom rows of tails directly above each other, with no stagger. There's no datasheet (3M's MCH-068 parts are the host-side headers), so the land pattern has to be measured from a sample. Buy enough for every board in one order. Ruled out: a generic AliExpress 68-pin female part (single-sided, but $39 shipping and over 2 weeks, and its photos show an AMP-marked part while it's sold as "Jiansu BST"), TE 5535657 (the host-side header), Hirose IC1K-68RD-1.27SF(71) (LCSC lists it as "Connector and Ejector", which reads as the host-side socket), Hirose IC1F-68RD-1.27SF and IC9 (obsolete), Amphenol 10014744-007T and 71299-050CALF (out of production), and Amphenol 7111S1615A01LF (a SIM card tray). The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, the gap between the two rows (the board thickness it takes), tail pitch, tail distance from the mating face, tail width and length, and the body size and any pegs. +- **Connector: the Hirose IC1HA order was cancelled (2026-11-17).** Candidate: 3M MCS-068SMA1-TR30, a 68-contact female PCMCIA receptacle for memory cards ("MEMPAK"), straddle mount, sold on eBay as surplus. It's a Robinson Nugent part (later 3M). The only document found is a catalogue overview page (Robinson Nugent PC Card Products p. 330, "MEMPAK Receptacles"), which gives "PCMCIA Spec, .050\" straddle mount, SMT solder tails, Standard mounting ears" with no offset on the tails; its drawing is on catalogue p. 333, which hasn't turned up. So each row is 34 tails at 1.27 mm, and the listing photos show the two rows directly above each other, with no stagger. The gap between the rows (the board thickness) isn't given, so it and the rest of the land pattern have to be measured from a sample. The same page lists MCS-068SSA1-TR30: one row of 68 SMT tails at .025\" (0.635 mm) on one side of the board, top or bottom mounting. That would suit a single-sided board of any thickness, if one can be found. Buy enough for every board in one order. Ruled out: a generic AliExpress 68-pin female part (single-sided, but $39 shipping and over 2 weeks, and its photos show an AMP-marked part while it's sold as "Jiansu BST"), TE 5535657 (the host-side header), Hirose IC1K-68RD-1.27SF(71) (LCSC lists it as "Connector and Ejector", which reads as the host-side socket), Hirose IC1F-68RD-1.27SF and IC9 (obsolete), Amphenol 10014744-007T and 71299-050CALF (out of production), and Amphenol 7111S1615A01LF (a SIM card tray). The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, the gap between the two rows (the board thickness it takes), tail pitch, tail distance from the mating face, tail width and length, and the body size and any pegs. - **Case.** The keying is in the module case, so rev 2 needs a case (printed, or a harvested Springboard shell) whose key and latch match the slot, with the board held at the connector's height. Dry-fit a bare harvested connector in the slot to check the contacts seat fully. - **Board thickness.** A straddle connector sets it: the board is whatever fits between the two rows. The Hirose IC1HA took 1.6 mm, but PC Card internal boards are often about 0.8 mm, so measure the 3M part's gap before assuming 1.6 mm. - **LiPo size.** The aim is at least a few days per charge. Estimate, to be replaced by a measurement: