From e71f979dce4e7599bae80259687878af40d85071 Mon Sep 17 00:00:00 2001 From: "Rich O." Date: Thu, 19 Nov 2026 22:18:32 -0500 Subject: [PATCH] docs: SB-LoRa rev 2 connector: the AliExpress 68-pin female PCMCIA part is the J1 candidate (female side, both rows of tails flat on top per the listing photos); its land pattern waits on a measured sample, and the Hirose IC1K listing looks like a host-side socket --- hardware/sb-lora/REV2.md | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/hardware/sb-lora/REV2.md b/hardware/sb-lora/REV2.md index d137951..38ff868 100644 --- a/hardware/sb-lora/REV2.md +++ b/hardware/sb-lora/REV2.md @@ -68,7 +68,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc ## Open -- **Connector: the Hirose IC1HA order was cancelled (2026-11-17)**, so rev 2 drops the straddle footprint for a single-sided SMT PC Card receptacle (both rows of tails on the top side), harvested or stocked. No stocked candidate yet. Ruled out: TE 5535657 (the host-side header), Hirose IC1F-68RD-1.27SF and IC9 (obsolete), Amphenol 10014744-007T and 71299-050CALF (out of production), and Amphenol 7111S1615A01LF (a SIM card tray). "Amphenol 1C1K" never turned up as a real part number. The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, tail pitch, row spacing, tail distance from the mating face, and board surface height relative to the contact centre line. +- **Connector: the Hirose IC1HA order was cancelled (2026-11-17)**, so rev 2 drops the straddle footprint for a single-sided SMT PC Card receptacle (both rows of tails on the top side), harvested or stocked. Candidate: a generic 68-pin female PCMCIA connector sold on AliExpress for CF-to-PC Card adapters (https://www.aliexpress.com/item/32843057045.html, about $8.50 for 5). The listing photos show it's the female side, with both rows of tails flat on the top, but there's no drawing, so the land pattern has to be measured from a sample. Hirose IC1K-68RD-1.27SF(71) (LCSC C17285563) is listed as "Connector and Ejector", which reads as the host-side socket; it isn't confirmed either way. Ruled out: TE 5535657 (the host-side header), Hirose IC1F-68RD-1.27SF and IC9 (obsolete), Amphenol 10014744-007T and 71299-050CALF (out of production), and Amphenol 7111S1615A01LF (a SIM card tray). "Amphenol 1C1K" never turned up as a real part number. The Springboard uses the same 68-pin PCMCIA contacts (Dev Guide §5, §7.1), and the keying is in the module's plastic case, not the connector. Needed from a sample: markings, tail pitch, row spacing, tail distance from the mating face, and board surface height relative to the contact centre line. - **Case.** The keying is in the module case, so rev 2 needs a case (printed, or a harvested Springboard shell) whose key and latch match the slot, with the board held at the connector's height. Dry-fit a bare harvested connector in the slot to check the contacts seat fully. - **Board thickness.** The straddle connector forces 1.6 mm; a top-mount one may allow 0.8-1.0 mm. - **LiPo size.** The aim is at least a few days per charge. Estimate, to be replaced by a measurement: @@ -87,7 +87,7 @@ A 16550-style UART on csSlot1 replaces rev 1's SC16IS740 SPI bridge and its latc - **Renders:** `rev2/renders/`. Before ordering: -1. **J1.** Choose a card-side single-sided receptacle, then replace the `J1_*` constants at the top of `build_board.py` from its drawing: pitch, row stagger, each row's distance from the edge, and pad size. Keep the 5.5 mm strip along the edge free (`J1_KEEP`), and check whether the connector body needs the board edge moved. Then run `make.sh` and `make_fab.py` again. The current pattern is a placeholder: two staggered rows of 0.5 x 1.6 mm pads, 1.3 and 3.5 mm in from the edge. TE 5535657 is not a candidate: it's the host-side header. +1. **J1.** Get samples of the AliExpress candidate (above) and measure one with calipers. Then replace the `J1_*` constants at the top of `build_board.py` from its drawing: pitch, row stagger, each row's distance from the edge, and pad size. Keep the 5.5 mm strip along the edge free (`J1_KEEP`), and check whether the connector body needs the board edge moved. Then run `make.sh` and `make_fab.py` again. The current pattern is a placeholder: two staggered rows of 0.5 x 1.6 mm pads, 1.3 and 3.5 mm in from the edge. TE 5535657 is not a candidate: it's the host-side header. 2. **XIAO and Wio footprints.** Check them against the real boards with calipers (print the top copper at 1:1). 3. **Assembly.** In JLC's placement preview, check the rotation of U1 (pin 1 at the top left, beside the triangle), U2, U3, U5 and Y1. 4. **Board thickness.** It stays 1.6 mm unless the chosen connector wants a thinner board.