From cf22b6dbdeea5b8f0bed7a990d360e344e749660 Mon Sep 17 00:00:00 2001 From: "Rich O." Date: Fri, 30 Oct 2026 13:57:15 -0400 Subject: [PATCH] sb-lora: replace out-of-stock crystal with SX3B14.7456F2010F30 (C2901666) SXT32413BA07 (C6264361) is out of stock at LCSC. Same 14.7456 MHz and 3225-4P footprint; 20 pF load vs 13 pF, so with the existing 22 pF caps it runs a few tens of ppm high, which is irrelevant for UART timing. --- hardware/sb-lora/README.md | 4 ++-- hardware/sb-lora/fab/visormesh_bom_jlcpcb.csv | 2 +- hardware/sb-lora/kicad/visormesh.kicad_pcb | 4 ++-- hardware/sb-lora/source/netlist.py | 2 +- 4 files changed, 6 insertions(+), 6 deletions(-) diff --git a/hardware/sb-lora/README.md b/hardware/sb-lora/README.md index 65d3a56..c65f591 100644 --- a/hardware/sb-lora/README.md +++ b/hardware/sb-lora/README.md @@ -24,7 +24,7 @@ A Springboard module for the Handspring Visor that carries a Seeed XIAO nRF52840 - PCB: 2 layers, **1.6 mm**, 1 oz, any color. **ENIG recommended** (flat pads for the 0.65 mm TSSOP, SC-70 parts and the straddle connector); lead-free HASL works too. - Board is 50.43 x 75.15 mm. The bottom 50.47 mm is the in-slot section, using springSD's exact outline. The top 24.6 mm sticks out of the Visor and carries the XIAO stack. - Assembly: top side, Economic PCBA is fine. Upload BOM + CPL. **Check part rotations in JLC's placement preview** before paying, especially U1-U7, Y1 and D1; KiCad and JLC disagree on rotation for some SOT/SC-70 footprints. Pin 1 of each IC is marked on the silkscreen and assembly drawing. -- Extended parts: SC16IS740 (C407851), 74LVC1G80 (C353857), crystal (C6264361) and probably the SN74LVC1T45 (C9382) and 74LVC1G04 (C10237). Expect extended-part loading fees. +- Extended parts: SC16IS740 (C407851), 74LVC1G80 (C353857), crystal (C2901666) and probably the SN74LVC1T45 (C9382) and 74LVC1G04 (C10237). Expect extended-part loading fees. ## Parts you fit by hand @@ -45,7 +45,7 @@ A Springboard module for the Handspring Visor that carries a Seeed XIAO nRF52840 - A CS0* access latches A17 and A8 on its rising edge. Through Q-bar, `nCS = NOT A17` and `MOSI = NOT A8`. - A CS1* read produces one SCLK pulse; MISO comes back on D0 through a 1k resistor. - SC16IS740 is SPI mode 0. Register byte: bit7 = R/W (1 = read), bits 6:3 = register, bits 2:1 = channel 00. -- **UART**: 14.7456 MHz crystal, so 115200 baud with DLL=8, DLH=0 (prescaler 1). 64-byte TX/RX FIFOs. IRQ* goes straight to the Springboard IRQ* (the Visor has the pull-up). RESET* follows the slot RESET*. +- **UART**: 14.7456 MHz crystal (SCTF SX3B14.7456F2010F30, 20 pF load; replaced the out-of-stock SXT32413BA07 rated 13 pF), so 115200 baud with DLL=8, DLH=0 (prescaler 1). 64-byte TX/RX FIFOs. IRQ* goes straight to the Springboard IRQ* (the Visor has the pull-up). RESET* follows the slot RESET*. - **Power isolation**: only U5-U7 (SN74LVC1T45) touch both domains, and both of their ports go Hi-Z when either supply is 0 V. Removing the module, a LOWBAT power cut, or a flat LiPo can't back-power the other side. - **Visor-present**: XIAO D0 is high when the slot is powered. The firmware can stop pushing frames when it's low; the companion queues messages anyway. - **Slot budget**: a few mA active, against the 100 mA limit. To stay inside the 100 uA standby limit, put the SC16IS740 to sleep (IER bit 4) when the Palm app is idle. diff --git a/hardware/sb-lora/fab/visormesh_bom_jlcpcb.csv b/hardware/sb-lora/fab/visormesh_bom_jlcpcb.csv index ef3cb18..3061113 100644 --- a/hardware/sb-lora/fab/visormesh_bom_jlcpcb.csv +++ b/hardware/sb-lora/fab/visormesh_bom_jlcpcb.csv @@ -9,4 +9,4 @@ B5819W,D1,D_SOD-123,C8598 74LVC1G04GW,U3,SOT-353_SC-70-5,C10237 SC16IS740IPW,U4,TSSOP-16_4.4x5mm_P0.65mm,C407851 SN74LVC1T45DCKR,"U5,U6,U7",SOT-363_SC-70-6,C9382 -14.7456MHz 13pF,Y1,Crystal_SMD_3225-4Pin_3.2x2.5mm,C6264361 +14.7456MHz 20pF,Y1,Crystal_SMD_3225-4Pin_3.2x2.5mm,C2901666 diff --git a/hardware/sb-lora/kicad/visormesh.kicad_pcb b/hardware/sb-lora/kicad/visormesh.kicad_pcb index db08130..73abc8d 100644 --- a/hardware/sb-lora/kicad/visormesh.kicad_pcb +++ b/hardware/sb-lora/kicad/visormesh.kicad_pcb @@ -878,13 +878,13 @@ (at 108 101.5 90) (descr "SMD Crystal SERIES SMD3225/4 http://www.txccrystal.com/images/pdf/7m-accuracy.pdf, 3.2x2.5mm^2 package") (tags "SMD SMT crystal") - (property "LCSC" "C6264361") + (property "LCSC" "C2901666") (attr smd) (fp_text reference "Y1" (at 0 -2.45 90) (layer "F.Fab") (effects (font (size 0.5 0.5) (thickness 0.08))) (tstamp 51331b93-533d-4aab-bbb8-eaa0417d8c8c) ) - (fp_text value "14.7456MHz 13pF" (at 0 2.45 90) (layer "F.Fab") hide + (fp_text value "14.7456MHz 20pF" (at 0 2.45 90) (layer "F.Fab") hide (effects (font (size 1 1) (thickness 0.15))) (tstamp 593d80aa-0e7f-4d29-8b1a-232f3761dc35) ) diff --git a/hardware/sb-lora/source/netlist.py b/hardware/sb-lora/source/netlist.py index ad6deba..bef69fa 100644 --- a/hardware/sb-lora/source/netlist.py +++ b/hardware/sb-lora/source/netlist.py @@ -24,7 +24,7 @@ PARTS = { "U5": ("SN74LVC1T45DCKR", "Package_TO_SOT_SMD", "SOT-363_SC-70-6", "C9382", "Ioff xlate: bridge TX -> XIAO D7", False), "U6": ("SN74LVC1T45DCKR", "Package_TO_SOT_SMD", "SOT-363_SC-70-6", "C9382", "Ioff xlate: XIAO D6 -> bridge RX", False), "U7": ("SN74LVC1T45DCKR", "Package_TO_SOT_SMD", "SOT-363_SC-70-6", "C9382", "Ioff xlate: Visor-present -> XIAO D0", False), - "Y1": ("14.7456MHz 13pF", "Crystal", "Crystal_SMD_3225-4Pin_3.2x2.5mm", "C6264361", "SXT32413BA07-14.7456M", False), + "Y1": ("14.7456MHz 20pF", "Crystal", "Crystal_SMD_3225-4Pin_3.2x2.5mm", "C2901666", "SX3B14.7456F2010F30", False), "C1": ("1uF", "Capacitor_SMD", "C_0603_1608Metric", "C15849", "VSB bulk", False), "C2": ("100nF", "Capacitor_SMD", "C_0603_1608Metric", "C14663", "U1 decoupling", False), "C3": ("100nF", "Capacitor_SMD", "C_0603_1608Metric", "C14663", "U2 decoupling", False),