MeshTerm now announces the connected node by itself: a zero-hop advert
every 1/2/3/4 hours (default hourly) and a flood advert every
3/6/12/24/48/168 hours (default daily), each switchable off. The
cadences are staged and applied from a new Background adverts section
in the device-configuration editor, and persist per device (keyed by
public key) in adverts.json alongside the last-sent mark for each type
— so the countdown survives restarts, and a manual send from any
advert flow resets the same clock the scheduler reads.
The scheduler stays transmission-shy: at most one advert per 30 s pass
(a flood due together with a direct waits a pass), and a never-sent
device is armed to count from now rather than advertised immediately.
It holds no device subscription — each pass just skips when nothing is
connected — so reconnects need no special handling, and scripted CLI
runs never start it.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Announcing the node is the everyday operation in the Device actions
bucket, but it sat two screens deep and out of reach of the main menu's
type-to-filter. Give it a top-level entry (order 10, right after Device
actions; Device info shifts to 11) via a new menu-only tool that reuses
the existing advert flow through a standalone send_advert() entry point.
Only SELF_INFO is read on open — the advert op and contact card never
need the full snapshot — so it stays snappy over Bluetooth. The row
inside Device actions stays, and scripting remains under `config
advert` / `config share`, so no new CLI subcommand.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
New staged settings: contact auto-add bitmask, default flood scope
(hashtag-normalized, 31-byte slot), and the two TX delay factors the
library always zeroed (write-only on hardware, so unknown values fall
back to 0 exactly as before). TX power is now capped by the board's
reported max_tx_power instead of a hardcoded 22, with the prompt hint
and validation sharing one effective_maximum.
Device actions gain Sync clock (drift shown before writing host time;
also a config sync-clock CLI command), and Device info now leads with
a live Status panel: role, model/firmware, battery, storage, clock
drift, uptime, and radio/packet statistics — every read best-effort so
older firmware still renders.
The simulator models all of it, including a seeded clock drift.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
- Dialog footer hints take the border's hue one shade darker (hint.*
theme styles), mirroring the brighter title tinting.
- Dialogs get a blank breathing row above and below the body whenever
it doesn't cost visible content.
- The chat conversation picker gains column headers over its lanes.
- The map screen titles itself "Map", matching its menu item.
- The config editor lays settings out in aligned SETTING / VALUE /
DESCRIPTION columns under a header line, and with changes staged the
Apply and Back rows sit together below the blank separator.
- Device actions move out of the config editor into their own screen
behind a new menu-only device-actions tool (CLI equivalents stay
under the config group).
- Type-to-filter keeps section headers (and column headers) in place,
and section jumps now work over the filtered rows too.
- The main menu aligns tool names and muted descriptions into two
columns, headerless.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Rework the device-configuration screen from a flat list with an
advert-laden "danger zone" into one grouped menu whose every prompt is
a real floating modal popup over a persistent backdrop, matching the
quit dialog. The main menu now stays pushed on the session stack for
the whole editor session, so sub-prompts float over it rather than
replacing the screen.
Settings are staged and applied together (with a dirty-cancel
confirmation); device actions — adverts, reboot, backup/restore,
identity key, factory reset — run immediately behind their own
dialogs. Adverts get a dedicated menu (zero-hop, flood, or share this
node as a QR/URI contact card). Destructive actions gate behind a new
TypedConfirmDialog that requires typing RESET / IMPORT. Reboot hands
off to the reconnect dialog and waits for the companion to return.
Location can be set by pointing at the full-screen map (new
LocationPickScreen) or by typing coordinates.
Make every dialog consistent: a short title in the border, the
instruction as an in-body prompt, and a width sized to its content
instead of a fixed wide cap. TextScreen/SelectScreen/AutocompleteScreen
gain an optional in-body prompt, and those plus ConfirmScreen gain a
dialog_width; the prompt is threaded through the surface and session.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Jean-Pierre MartineauandClaude Fable 5