Bring in the new Companion WiFi profiles while preserving existing OLED detection, message queues and OTA safeguards. Include dynamic WiFi helpers consistently and refresh the affected test fixtures.
950 lines
30 KiB
INI
950 lines
30 KiB
INI
[Heltec_lora32_v4]
|
|
extends = esp32_base
|
|
board = heltec_v4
|
|
build_flags =
|
|
${esp32_base.build_flags}
|
|
${sensor_base.build_flags}
|
|
-I variants/heltec_v4
|
|
-D HELTEC_LORA_V4
|
|
-D USE_SX1262
|
|
-D ARDUINO_USB_MODE=1 ; ARDUINO_USB_MODE in heltec_v4.json has no effect
|
|
-D ESP32_CPU_FREQ=80
|
|
-D RADIO_CLASS=CustomSX1262
|
|
-D WRAPPER_CLASS=CustomSX1262Wrapper
|
|
-D P_LORA_TX_LED=35
|
|
-D P_LORA_DIO_1=14
|
|
-D P_LORA_NSS=8
|
|
-D P_LORA_RESET=12
|
|
-D P_LORA_BUSY=13
|
|
-D P_LORA_SCLK=9
|
|
-D P_LORA_MISO=11
|
|
-D P_LORA_MOSI=10
|
|
-D P_LORA_PA_POWER=7 ; // VFEM_Ctrl -LDO power enable
|
|
-D P_LORA_GC1109_PA_EN=2 ; // CSD - GC1109 chip enable (HIGH=on)
|
|
-D P_LORA_GC1109_PA_TX_EN=46 ;// CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
|
|
-D P_LORA_KCT8103L_PA_CSD=2
|
|
-D P_LORA_KCT8103L_PA_CTX=5
|
|
-D PIN_USER_BTN=0
|
|
-D MOMENTARY_BUTTON_WAKE_FROM_SLEEP=1
|
|
-D PIN_VEXT_EN=36
|
|
-D PIN_VEXT_EN_ACTIVE=HIGH
|
|
-D LORA_TX_POWER=22 ; Default to maximum SX1262 drive
|
|
-D MAX_LORA_TX_POWER=22 ; Max SX1262 output
|
|
-D SX126X_REGISTER_PATCH=1 ; Patch register 0x8B5 for improved RX
|
|
-D SX126X_DIO2_AS_RF_SWITCH=true ; GC1109 CTX is controlled by SX1262 DIO2
|
|
-D SX126X_DIO3_TCXO_VOLTAGE=1.8
|
|
-D SX126X_CURRENT_LIMIT=140
|
|
-D SX126X_RX_BOOSTED_GAIN=1 ; In some cases, commenting this out will improve RX
|
|
-D PIN_GPS_RX=38
|
|
-D PIN_GPS_TX=39
|
|
-D PIN_GPS_RESET=42
|
|
-D PIN_GPS_RESET_ACTIVE=LOW
|
|
-D PIN_GPS_EN=34
|
|
-D PIN_GPS_EN_ACTIVE=LOW
|
|
-D ENV_INCLUDE_GPS=1
|
|
-D PIN_ADC_CTRL=37
|
|
-D PIN_VBAT_READ=1
|
|
build_src_filter = ${esp32_base.build_src_filter}
|
|
+<../variants/heltec_v4>
|
|
+<helpers/sensors>
|
|
lib_deps =
|
|
${esp32_base.lib_deps}
|
|
${sensor_base.lib_deps}
|
|
|
|
[heltec_v4_oled]
|
|
extends = Heltec_lora32_v4
|
|
build_flags =
|
|
${Heltec_lora32_v4.build_flags}
|
|
-D HELTEC_LORA_V4_OLED
|
|
-D HELTEC_V4_OLED_KIT_COMPAT=1
|
|
-D PIN_BOARD_SDA=17
|
|
-D PIN_BOARD_SCL=18
|
|
; The OLED uses Wire above; the expansion/general sensor connector is 4/3.
|
|
-D ENV_PIN_SDA=4
|
|
-D ENV_PIN_SCL=3
|
|
-D PIN_OLED_RESET=21
|
|
build_src_filter= ${Heltec_lora32_v4.build_src_filter}
|
|
lib_deps = ${Heltec_lora32_v4.lib_deps}
|
|
|
|
[heltec_v4_tft]
|
|
extends = Heltec_lora32_v4
|
|
build_flags =
|
|
${Heltec_lora32_v4.build_flags}
|
|
-D HELTEC_LORA_V4_TFT
|
|
-D HELTEC_V4_TFT_KIT_COMPAT=1
|
|
-D PIN_BOARD_SDA=4
|
|
-D PIN_BOARD_SCL=3
|
|
-D PIN_TFT_RST=18
|
|
-D PIN_TFT_VDD_CTL=-1
|
|
-D PIN_TFT_LEDA_CTL=21
|
|
-D PIN_TFT_LEDA_CTL_ACTIVE=HIGH
|
|
-D PIN_TFT_CS=15
|
|
-D PIN_TFT_DC=16
|
|
-D PIN_TFT_SCL=17
|
|
-D PIN_TFT_SDA=33
|
|
build_src_filter= ${Heltec_lora32_v4.build_src_filter}
|
|
lib_deps =
|
|
${Heltec_lora32_v4.lib_deps}
|
|
adafruit/Adafruit ST7735 and ST7789 Library @ ^1.11.0
|
|
|
|
[env:heltec_v4_repeater]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"Heltec Repeater"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
bakercp/CRC32 @ ^2.0.0
|
|
|
|
[env:heltec_v4_repeater_legacy_partition_test]
|
|
; Deliberately retains Arduino's 1.25 MiB OTA slots for validating the
|
|
; Wi-Fi-only partition migration bridge on disposable hardware.
|
|
extends = heltec_v4_oled
|
|
board_build.partitions = default.csv
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"Heltec Repeater"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
bakercp/CRC32 @ ^2.0.0
|
|
|
|
[env:heltec_v4_expansionkit_repeater]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"Heltec Repeater"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
-D ENV_PIN_SDA=4
|
|
-D ENV_PIN_SCL=3
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
bakercp/CRC32 @ ^2.0.0
|
|
|
|
[env:heltec_v4_repeater_bridge_espnow]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"ESPNow Bridge"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
-D WITH_ESPNOW_BRIDGE=1
|
|
; -D BRIDGE_DEBUG=1
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/bridges/ESPNowBridge.cpp>
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
[env:heltec_v4_repeater_observer_mqtt]
|
|
extends = heltec_v4_oled
|
|
extra_scripts =
|
|
${esp32_base.extra_scripts}
|
|
pre:scripts/generate_cert_bundle.py
|
|
board_ssl_cert_source = adafruit-full
|
|
board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"MQTT Observer"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
-D WITH_MQTT_BRIDGE=1
|
|
-D MQTT_MAX_PACKET_SIZE=1024
|
|
-D MQTT_DEBUG=1
|
|
; -D MQTT_MEMORY_DEBUG=1
|
|
; Keep default observer profile less verbose to reduce runtime contention.
|
|
; Use heltec_v4_repeater_observer_mqtt_debug for deep troubleshooting.
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
|
|
-D ESP32_CPU_FREQ=160
|
|
-D MQTT_WIFI_TX_POWER=WIFI_POWER_11dBm
|
|
-D WITH_SNMP=1
|
|
# -D WIFI_SSID='"ssid"'
|
|
# -D WIFI_PWD='"password"'
|
|
# -D MQTT_SERVER='"your-mqtt-broker.com"'
|
|
# -D MQTT_PORT=1883
|
|
# -D MQTT_USERNAME='"your-username"'
|
|
# -D MQTT_PASSWORD='"your-password"'
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/bridges/MQTTBridge.cpp>
|
|
+<helpers/MQTTMessageBuilder.cpp>
|
|
+<helpers/JWTHelper.cpp>
|
|
+<helpers/SNMPAgent.cpp>
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
elims/PsychicMqttClient@^0.2.4
|
|
bblanchon/ArduinoJson @ 7.4.3
|
|
arduino-libraries/NTPClient
|
|
JChristensen/Timezone
|
|
paulstoffregen/Time@1.6.1
|
|
0neblock/SNMP_Agent
|
|
|
|
[env:heltec_v4_expansionkit_repeater_observer_mqtt]
|
|
extends = heltec_v4_oled
|
|
extra_scripts =
|
|
${esp32_base.extra_scripts}
|
|
pre:scripts/generate_cert_bundle.py
|
|
board_ssl_cert_source = adafruit-full
|
|
board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"MQTT Observer"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
-D WITH_MQTT_BRIDGE=1
|
|
-D MQTT_MAX_PACKET_SIZE=1024
|
|
-D MQTT_DEBUG=1
|
|
; -D MQTT_MEMORY_DEBUG=1
|
|
; Keep default observer profile less verbose to reduce runtime contention.
|
|
; Use heltec_v4_repeater_observer_mqtt_debug for deep troubleshooting.
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
|
|
-D ESP32_CPU_FREQ=160
|
|
-D MQTT_WIFI_TX_POWER=WIFI_POWER_11dBm
|
|
-D WITH_SNMP=1
|
|
-D ENV_PIN_SDA=4
|
|
-D ENV_PIN_SCL=3
|
|
# -D WIFI_SSID='"ssid"'
|
|
# -D WIFI_PWD='"password"'
|
|
# -D MQTT_SERVER='"your-mqtt-broker.com"'
|
|
# -D MQTT_PORT=1883
|
|
# -D MQTT_USERNAME='"your-username"'
|
|
# -D MQTT_PASSWORD='"your-password"'
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/bridges/MQTTBridge.cpp>
|
|
+<helpers/MQTTMessageBuilder.cpp>
|
|
+<helpers/JWTHelper.cpp>
|
|
+<helpers/SNMPAgent.cpp>
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
elims/PsychicMqttClient@^0.2.4
|
|
bblanchon/ArduinoJson @ 7.4.3
|
|
arduino-libraries/NTPClient
|
|
JChristensen/Timezone
|
|
paulstoffregen/Time@1.6.1
|
|
0neblock/SNMP_Agent
|
|
|
|
#[env:heltec_v4_repeater_observer_mqtt_debug]
|
|
#extends = heltec_v4_oled
|
|
#extra_scripts =
|
|
# ${esp32_base.extra_scripts}
|
|
# pre:scripts/generate_cert_bundle.py
|
|
#board_ssl_cert_source = adafruit-full
|
|
#board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
#build_flags =
|
|
# ${env:heltec_v4_repeater_observer_mqtt.build_flags}
|
|
# -D MQTT_MEMORY_DEBUG=1
|
|
# -D MESH_PACKET_LOGGING=1
|
|
# -D MESH_DEBUG=1
|
|
#build_src_filter = ${env:heltec_v4_repeater_observer_mqtt.build_src_filter}
|
|
#lib_deps =
|
|
# ${env:heltec_v4_repeater_observer_mqtt.lib_deps}
|
|
|
|
#[env:heltec_v4_repeater_observer_mqtt_quiet]
|
|
#extends = heltec_v4_oled
|
|
#extra_scripts =
|
|
# ${esp32_base.extra_scripts}
|
|
# pre:scripts/generate_cert_bundle.py
|
|
#board_ssl_cert_source = adafruit-full
|
|
#board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
#build_flags =
|
|
# ${env:heltec_v4_repeater_observer_mqtt.build_flags}
|
|
#build_unflags =
|
|
# -D MQTT_DEBUG=1
|
|
# -D MQTT_MEMORY_DEBUG=1
|
|
#build_src_filter = ${env:heltec_v4_repeater_observer_mqtt.build_src_filter}
|
|
#lib_deps =
|
|
# ${env:heltec_v4_repeater_observer_mqtt.lib_deps}
|
|
|
|
#[env:heltec_v4_repeater_observer_mqtt_quiet_keepalive45]
|
|
#extends = heltec_v4_oled
|
|
#extra_scripts =
|
|
# ${esp32_base.extra_scripts}
|
|
# pre:scripts/generate_cert_bundle.py
|
|
#board_ssl_cert_source = adafruit-full
|
|
#board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
#build_flags =
|
|
# ${env:heltec_v4_repeater_observer_mqtt.build_flags}
|
|
# -D MQTT_FORCE_KEEPALIVE_45=1
|
|
#build_unflags =
|
|
# -D MQTT_DEBUG=1
|
|
# -D MQTT_MEMORY_DEBUG=1
|
|
#build_src_filter = ${env:heltec_v4_repeater_observer_mqtt.build_src_filter}
|
|
#lib_deps =
|
|
# ${env:heltec_v4_repeater_observer_mqtt.lib_deps}
|
|
|
|
[env:heltec_v4_room_server_observer_mqtt]
|
|
extends = heltec_v4_oled
|
|
extra_scripts =
|
|
${esp32_base.extra_scripts}
|
|
pre:scripts/generate_cert_bundle.py
|
|
board_ssl_cert_source = adafruit-full
|
|
board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"Heltec Room Observer"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D ROOM_PASSWORD='"hello"'
|
|
-D WITH_MQTT_BRIDGE=1
|
|
-D MAX_NEIGHBOURS=50
|
|
-D MQTT_MAX_PACKET_SIZE=1024
|
|
-D MQTT_DEBUG=1
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
|
|
-D ESP32_CPU_FREQ=160
|
|
-D MQTT_WIFI_TX_POWER=WIFI_POWER_11dBm
|
|
-D WITH_SNMP=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/bridges/MQTTBridge.cpp>
|
|
+<helpers/MQTTMessageBuilder.cpp>
|
|
+<helpers/JWTHelper.cpp>
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<helpers/SNMPAgent.cpp>
|
|
+<../examples/simple_room_server>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
elims/PsychicMqttClient@^0.2.4
|
|
bblanchon/ArduinoJson @ 7.4.3
|
|
arduino-libraries/NTPClient
|
|
JChristensen/Timezone
|
|
paulstoffregen/Time@1.6.1
|
|
0neblock/SNMP_Agent
|
|
|
|
[env:heltec_v4_expansionkit_room_server_observer_mqtt]
|
|
extends = heltec_v4_oled
|
|
extra_scripts =
|
|
${esp32_base.extra_scripts}
|
|
pre:scripts/generate_cert_bundle.py
|
|
board_ssl_cert_source = adafruit-full
|
|
board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"Heltec Room Observer"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D ROOM_PASSWORD='"hello"'
|
|
-D WITH_MQTT_BRIDGE=1
|
|
-D MAX_NEIGHBOURS=50
|
|
-D MQTT_MAX_PACKET_SIZE=1024
|
|
-D MQTT_DEBUG=1
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
|
|
-D ESP32_CPU_FREQ=160
|
|
-D MQTT_WIFI_TX_POWER=WIFI_POWER_11dBm
|
|
-D ENV_PIN_SDA=4
|
|
-D ENV_PIN_SCL=3
|
|
-D WITH_SNMP=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/bridges/MQTTBridge.cpp>
|
|
+<helpers/MQTTMessageBuilder.cpp>
|
|
+<helpers/JWTHelper.cpp>
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<helpers/SNMPAgent.cpp>
|
|
+<../examples/simple_room_server>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
elims/PsychicMqttClient@^0.2.4
|
|
bblanchon/ArduinoJson @ 7.4.3
|
|
arduino-libraries/NTPClient
|
|
JChristensen/Timezone
|
|
paulstoffregen/Time@1.6.1
|
|
0neblock/SNMP_Agent
|
|
|
|
[env:heltec_v4_room_server]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ADVERT_NAME='"Heltec Room"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D ROOM_PASSWORD='"hello"'
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_room_server>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
[env:heltec_v4_terminal_chat]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=1
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<../examples/simple_secure_chat/main.cpp>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_companion_radio_usb_femon]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-I examples/companion_radio/ui-new
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=40
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D ENABLE_USB_INTERFACE
|
|
; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1
|
|
; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1
|
|
-D RADIO_FEM_RXGAIN=1 ; undefined (default), 1=on, 0=off
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<helpers/ui/MomentaryButton.cpp>
|
|
+<../examples/companion_radio/*.cpp>
|
|
+<../examples/companion_radio/ui-new/*.cpp>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_3_companion_radio_usb_femoff]
|
|
extends = env:heltec_v4_companion_radio_usb_femon
|
|
build_flags =
|
|
${env:heltec_v4_companion_radio_usb_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_companion_radio_usb]
|
|
extends = env:heltec_v4_companion_radio_usb_femon
|
|
|
|
[env:heltec_v4_companion_radio_usb_ps_femon]
|
|
extends = env:heltec_v4_companion_radio_usb_femon
|
|
|
|
[env:heltec_v4_companion_radio_usb_ps_femoff]
|
|
extends = env:heltec_v4_3_companion_radio_usb_femoff
|
|
|
|
[env:heltec_v4_companion_radio_ble_femon]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-I examples/companion_radio/ui-new
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=40
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D BLE_PIN_CODE=123456 ; dynamic, random PIN
|
|
-D AUTO_SHUTDOWN_MILLIVOLTS=3400
|
|
-D BLE_DEBUG_LOGGING=1
|
|
-D OFFLINE_QUEUE_SIZE=512
|
|
-D ENABLE_WIFI_INTERFACE
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
-D RADIO_FEM_RXGAIN=1 ; undefined (default), 1=on, 0=off
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<helpers/ui/MomentaryButton.cpp>
|
|
+<helpers/esp32/*.cpp>
|
|
+<helpers/wifi/*.cpp>
|
|
+<../examples/companion_radio/*.cpp>
|
|
+<../examples/companion_radio/ui-new/*.cpp>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_companion_radio_ble_femoff]
|
|
extends = env:heltec_v4_companion_radio_ble_femon
|
|
build_flags =
|
|
${env:heltec_v4_companion_radio_ble_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
; Preserve the previously published target name as an alias.
|
|
[env:heltec_v4_3_companion_radio_ble_femoff]
|
|
extends = env:heltec_v4_companion_radio_ble_femoff
|
|
|
|
[env:heltec_v4_companion_radio_ble]
|
|
extends = env:heltec_v4_companion_radio_ble_femon
|
|
|
|
[env:heltec_v4_companion_radio_ble_ps_femon]
|
|
extends = env:heltec_v4_companion_radio_ble_femon
|
|
|
|
[env:heltec_v4_3_companion_radio_ble_ps_femoff]
|
|
extends = env:heltec_v4_3_companion_radio_ble_femoff
|
|
|
|
[env:heltec_v4_companion_radio_wifi_femon]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-I examples/companion_radio/ui-new
|
|
-D ENABLE_WIFI_INTERFACE
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=40
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
-D WIFI_DEBUG_LOGGING=1
|
|
-D WIFI_SSID='"myssid"'
|
|
-D WIFI_PWD='"mypwd"'
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<helpers/ui/MomentaryButton.cpp>
|
|
+<helpers/esp32/*.cpp>
|
|
+<helpers/wifi/*.cpp>
|
|
+<../examples/companion_radio/*.cpp>
|
|
+<../examples/companion_radio/ui-new/*.cpp>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_3_companion_radio_wifi_femoff]
|
|
extends = env:heltec_v4_companion_radio_wifi_femon
|
|
build_flags =
|
|
${env:heltec_v4_companion_radio_wifi_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_companion_radio_wifi_mqtt_femon]
|
|
extends = env:heltec_v4_companion_radio_wifi_femon
|
|
extra_scripts =
|
|
${esp32_base.extra_scripts}
|
|
pre:scripts/generate_cert_bundle.py
|
|
board_ssl_cert_source = adafruit-full
|
|
board_build.embed_files = src/certs/x509_crt_bundle.bin
|
|
build_flags =
|
|
${env:heltec_v4_companion_radio_wifi_femon.build_flags}
|
|
-D WITH_MQTT_BRIDGE=1
|
|
-D MQTT_RUNTIME_SLOT_COUNT=1
|
|
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
|
|
-D ESP32_CPU_FREQ=160
|
|
-D MQTT_WIFI_TX_POWER=WIFI_POWER_11dBm
|
|
build_src_filter = ${env:heltec_v4_companion_radio_wifi_femon.build_src_filter}
|
|
+<helpers/bridges/MQTTBridge.cpp>
|
|
+<helpers/MQTTMessageBuilder.cpp>
|
|
+<helpers/JWTHelper.cpp>
|
|
lib_deps =
|
|
${env:heltec_v4_companion_radio_wifi_femon.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
elims/PsychicMqttClient@^0.2.4
|
|
bblanchon/ArduinoJson @ 7.4.3
|
|
arduino-libraries/NTPClient
|
|
JChristensen/Timezone
|
|
paulstoffregen/Time@1.6.1
|
|
|
|
[env:heltec_v4_3_companion_radio_wifi_mqtt_femoff]
|
|
extends = env:heltec_v4_companion_radio_wifi_mqtt_femon
|
|
build_flags =
|
|
${env:heltec_v4_companion_radio_wifi_mqtt_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
; Full Companion subsumes the former direct-MQTT Companion so this is the one
|
|
; canonical V4 OLED image. Arduino-ESP32 2.x exposes one USB TTY; enabling USB
|
|
; logging gives that TTY exclusively to the plaintext CLI/logging stream until
|
|
; logging is disabled again.
|
|
[env:heltec_v4_2_v4_3_companion_radio_full_femon]
|
|
extends = env:heltec_v4_companion_radio_wifi_mqtt_femon
|
|
; Marking the merged image QIO makes this V4 reset in the ROM before the
|
|
; software bootloader can start. Keep the Full image on the shared DIO policy.
|
|
board_build.flash_mode = ${esp32_s3_full.board_build.flash_mode}
|
|
build_flags =
|
|
${env:heltec_v4_companion_radio_wifi_mqtt_femon.build_flags}
|
|
-D MESHCORE_REQUIRES_COMPANION_RADIO_FULL=1
|
|
-D UI_WIFI_SETUP_HOME_PAGE=1
|
|
|
|
[env:heltec_v4_3_companion_radio_full_femoff]
|
|
extends = env:heltec_v4_3_companion_radio_wifi_mqtt_femoff
|
|
board_build.flash_mode = ${esp32_s3_full.board_build.flash_mode}
|
|
build_flags =
|
|
${env:heltec_v4_3_companion_radio_wifi_mqtt_femoff.build_flags}
|
|
-D MESHCORE_REQUIRES_COMPANION_RADIO_FULL=1
|
|
-D UI_WIFI_SETUP_HOME_PAGE=1
|
|
|
|
[env:heltec_v4_sensor]
|
|
extends = heltec_v4_oled
|
|
build_flags =
|
|
${heltec_v4_oled.build_flags}
|
|
-D ADVERT_NAME='"Heltec v4 Sensor"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D DISPLAY_CLASS=SSD1306Display
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_oled.build_src_filter}
|
|
+<helpers/ui/SSD1306Display.cpp>
|
|
+<../examples/simple_sensor>
|
|
lib_deps =
|
|
${heltec_v4_oled.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
|
|
[env:heltec_v4_tft_repeater]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
-D ADVERT_NAME='"Heltec Repeater"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
bakercp/CRC32 @ ^2.0.0
|
|
|
|
|
|
[env:heltec_v4_tft_repeater_bridge_espnow]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
-D ADVERT_NAME='"ESPNow Bridge"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D MAX_NEIGHBOURS=50
|
|
-D WITH_ESPNOW_BRIDGE=1
|
|
; -D BRIDGE_DEBUG=1
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/bridges/ESPNowBridge.cpp>
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<../examples/simple_repeater>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
[env:heltec_v4_tft_room_server]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
-D ADVERT_NAME='"Heltec Room"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
-D ROOM_PASSWORD='"hello"'
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<../examples/simple_room_server>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
[env:heltec_v4_tft_terminal_chat]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=1
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<../examples/simple_secure_chat/main.cpp>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_tft_companion_radio_usb_femon]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-I examples/companion_radio/ui-new
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=40
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
-D ENABLE_USB_INTERFACE
|
|
; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1
|
|
; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<helpers/ui/MomentaryButton.cpp>
|
|
+<../examples/companion_radio/*.cpp>
|
|
+<../examples/companion_radio/ui-new/*.cpp>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_3_tft_companion_radio_usb_femoff]
|
|
extends = env:heltec_v4_tft_companion_radio_usb_femon
|
|
build_flags =
|
|
${env:heltec_v4_tft_companion_radio_usb_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_tft_companion_radio_ble_femon]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-I examples/companion_radio/ui-new
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=40
|
|
-D BLE_PIN_CODE=123456 ; dynamic, random PIN
|
|
-D AUTO_SHUTDOWN_MILLIVOLTS=3400
|
|
-D BLE_DEBUG_LOGGING=1
|
|
-D OFFLINE_QUEUE_SIZE=512
|
|
-D ENABLE_WIFI_INTERFACE
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<helpers/ui/MomentaryButton.cpp>
|
|
+<helpers/esp32/*.cpp>
|
|
+<helpers/wifi/*.cpp>
|
|
+<../examples/companion_radio/*.cpp>
|
|
+<../examples/companion_radio/ui-new/*.cpp>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_3_tft_companion_radio_ble_femoff]
|
|
extends = env:heltec_v4_tft_companion_radio_ble_femon
|
|
build_flags =
|
|
${env:heltec_v4_tft_companion_radio_ble_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_expansionkit_tft_companion_radio_ble_femon]
|
|
extends = env:heltec_v4_tft_companion_radio_ble_femon
|
|
build_flags =
|
|
${env:heltec_v4_tft_companion_radio_ble_femon.build_flags}
|
|
; The TFT profile already uses Wire at the expansion I2C pins, GPIO4/3.
|
|
|
|
[env:heltec_v4_3_expansionkit_tft_companion_radio_ble_femoff]
|
|
extends = env:heltec_v4_expansionkit_tft_companion_radio_ble_femon
|
|
build_flags =
|
|
${env:heltec_v4_expansionkit_tft_companion_radio_ble_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_expansionkit_tft_companion_radio_ble_ps]
|
|
extends = env:heltec_v4_expansionkit_tft_companion_radio_ble_femon
|
|
|
|
; The original TFT expansion kit has the same TFT and GPIO4/3 sensor wiring.
|
|
; Keep its published environment/OTA identity as an exact hardware alias of
|
|
; the canonical Full recipe, including its low-battery protection.
|
|
[env:heltec_v4_expansionkit_tft_companion_radio_full_femon]
|
|
extends = env:heltec_v4_tft_companion_radio_full_femon
|
|
|
|
[env:heltec_v4_tft_companion_radio_wifi_femon]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-I examples/companion_radio/ui-new
|
|
-D ENABLE_WIFI_INTERFACE
|
|
-D MAX_CONTACTS=350
|
|
-D MAX_GROUP_CHANNELS=40
|
|
-D OFFLINE_QUEUE_SIZE=512
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
-D WIFI_DEBUG_LOGGING=1
|
|
-D WIFI_SSID='"myssid"'
|
|
-D WIFI_PWD='"mypwd"'
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<helpers/ui/MomentaryButton.cpp>
|
|
+<helpers/esp32/*.cpp>
|
|
+<helpers/wifi/*.cpp>
|
|
+<../examples/companion_radio/*.cpp>
|
|
+<../examples/companion_radio/ui-new/*.cpp>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
densaugeo/base64 @ ~1.4.0
|
|
|
|
[env:heltec_v4_3_tft_companion_radio_wifi_femoff]
|
|
extends = env:heltec_v4_tft_companion_radio_wifi_femon
|
|
build_flags =
|
|
${env:heltec_v4_tft_companion_radio_wifi_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_tft_companion_radio_full_femon]
|
|
extends = env:heltec_v4_tft_companion_radio_wifi_femon
|
|
board_build.flash_mode = ${esp32_s3_full.board_build.flash_mode}
|
|
build_flags =
|
|
${env:heltec_v4_tft_companion_radio_wifi_femon.build_flags}
|
|
-D AUTO_SHUTDOWN_MILLIVOLTS=3400
|
|
-D MESHCORE_REQUIRES_COMPANION_RADIO_FULL=1
|
|
|
|
[env:heltec_v4_3_tft_companion_radio_full_femoff]
|
|
extends = env:heltec_v4_tft_companion_radio_full_femon
|
|
build_flags =
|
|
${env:heltec_v4_tft_companion_radio_full_femon.build_flags}
|
|
-D RADIO_FEM_RXGAIN=0 ; undefined (default on), 1=on, 0=off
|
|
|
|
[env:heltec_v4_tft_sensor]
|
|
extends = heltec_v4_tft
|
|
build_flags =
|
|
${heltec_v4_tft.build_flags}
|
|
-D ADVERT_NAME='"Heltec v4 Sensor"'
|
|
-D ADVERT_LAT=0.0
|
|
-D ADVERT_LON=0.0
|
|
-D ADMIN_PASSWORD='"password"'
|
|
; Environmental sensors use the TFT profile's Wire bus at GPIO4/3.
|
|
-D DISPLAY_CLASS=ST7789LCDDisplay
|
|
; -D MESH_PACKET_LOGGING=1
|
|
; -D MESH_DEBUG=1
|
|
build_src_filter = ${heltec_v4_tft.build_src_filter}
|
|
+<helpers/ui/ST7789LCDDisplay.cpp>
|
|
+<../examples/simple_sensor>
|
|
lib_deps =
|
|
${heltec_v4_tft.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
[env:heltec_v4_kiss_modem]
|
|
extends = Heltec_lora32_v4
|
|
build_unflags =
|
|
-DARDUINO_USB_MODE=0
|
|
build_flags =
|
|
${Heltec_lora32_v4.build_flags}
|
|
-DARDUINO_USB_MODE=1
|
|
; KISS radio2 scanning stays on the board. This narrowly opts this target
|
|
; into the guarded SX1262 RX-to-RX fast path and buffered 8 MHz SPI. The
|
|
; host-powered modem also uses the established V4 160 MHz role override;
|
|
; normal V4 images retain their lower-power 80 MHz policy.
|
|
-D MC_SX1262_FAST_PROFILE_SWITCH=1
|
|
-D MC_SX1262_FAST_FS=1
|
|
-D MC_SX1262_FAST_PACKET_CACHE=1
|
|
-D MC_SX1262_BUFFERED_RADIO_HAL=1
|
|
-D MC_SX1262_SPI_HZ=8000000
|
|
-D ESP32_CPU_FREQ=160
|
|
build_src_filter = ${Heltec_lora32_v4.build_src_filter}
|
|
+<../examples/kiss_modem/>
|
|
|
|
; Self-hosted partition migration receiver for a legacy V4 1.25 MiB slot.
|
|
; This role keeps Wi-Fi recovery and receives the exact Full repeater over LoRa.
|
|
[env:heltec_v4_partition_expander]
|
|
extends = Heltec_lora32_v4
|
|
board = heltec_v4_migrator
|
|
board_build.partitions = default.csv
|
|
board_build.flash_mode = dio
|
|
board_upload.maximum_size = 1310720
|
|
build_src_filter = ${Heltec_lora32_v4.build_src_filter}
|
|
+<../examples/partition_expander/*.cpp>
|
|
build_flags = ${Heltec_lora32_v4.build_flags}
|
|
-D MESH_MIN_RUNTIME_HEAP=100352
|
|
-D MOTA_MIGRATION_TARGET_ID=0xe792a051
|
|
; Pipeline verified OTA blocks across one request turn. The adaptive window
|
|
; starts at one and grows only after clean flights, then shrinks on loss.
|
|
-D OTA_FETCH_PIPELINE=4
|
|
lib_deps = ${Heltec_lora32_v4.lib_deps}
|
|
${esp32_ota.lib_deps}
|
|
|
|
; One-time Wi-Fi-only migration bridge for legacy Heltec V4/V4.3 OLED
|
|
; repeaters that still use Arduino's 1.25 MiB OTA slots. It is linked against
|
|
; default.csv so the existing browser updater can install it.
|
|
[env:heltec_v4_partition_migrator]
|
|
platform = platformio/espressif32@6.11.0
|
|
board = heltec_v4_migrator
|
|
framework = arduino
|
|
board_build.partitions = default.csv
|
|
; The V4's ROM/bootloader chain is reliable with DIO. The final Full image
|
|
; uses the same setting, so there is no flash-mode transition after migration.
|
|
board_build.flash_mode = dio
|
|
; The partition-table erase disables the flash cache. Native USB CDC can still
|
|
; raise a flash-backed event ISR during that interval, even after Serial.end().
|
|
; The Wi-Fi-only bridge therefore keeps CDC disabled; the final regular
|
|
; repeater build restores its normal USB serial setting.
|
|
; This standalone image runs its own Wi-Fi OTA server. Reserve the generic
|
|
; ESP32 baseline plus its always-on Wi-Fi budget in the linked-image proof.
|
|
extra_scripts =
|
|
pre:scripts/esp32_wifi_scan_fix.py
|
|
post:scripts/check_firmware_ram.py
|
|
build_flags =
|
|
-D ESP32_PLATFORM
|
|
-D MESH_MIN_RUNTIME_HEAP=100352
|
|
-I variants/heltec_v4
|
|
build_src_filter =
|
|
-<*>
|
|
+<../examples/esp32_partition_migrator>
|
|
lib_deps =
|
|
ESP32Async/AsyncTCP @ 3.5.0
|
|
ESP32Async/ESPAsyncWebServer @ 3.12.0
|
|
file://arch/esp32/AsyncElegantOTA
|
|
|
|
; LoRa-delivered first stage for an OTA-enabled heltec_v4_repeater. It keeps
|
|
; that exact old application bootable after the table change, restores its
|
|
; private identity, and returns to it for the expanded-slot LoRa update.
|
|
[env:heltec_v4_partition_migrator_lora_repeater]
|
|
extends = env:heltec_v4_partition_migrator
|
|
build_flags =
|
|
${env:heltec_v4_partition_migrator.build_flags}
|
|
-D MESHCORE_MIGRATION_RESUME_OTA=1
|
|
|
|
; Disposable-hardware harness: leaves a ten-minute Wi-Fi OTA window for
|
|
; installing the production bridge into legacy slot B. This is not a release
|
|
; profile.
|
|
[env:heltec_v4_partition_migrator_test_hold]
|
|
extends = env:heltec_v4_partition_migrator
|
|
build_flags =
|
|
${env:heltec_v4_partition_migrator.build_flags}
|
|
-D MESHCORE_MIGRATION_DELAY_MS=600000
|
|
-D MESHCORE_MIGRATION_RESTART_DELAY_MS=0
|
|
|
|
; Harness-only diagnostic: USB CDC is restored so a failed AP startup can be
|
|
; distinguished from a board which never left its bootloader. It retains
|
|
; the same ten-minute no-write window as test_hold.
|
|
[env:heltec_v4_partition_migrator_test_usb_diagnostic]
|
|
extends = env:heltec_v4_partition_migrator_test_hold
|
|
build_flags =
|
|
${env:heltec_v4_partition_migrator_test_hold.build_flags}
|
|
-DARDUINO_USB_CDC_ON_BOOT=1
|