MeshCore/docs/nrf52_embedded_bootloader.md

View this page on MeshCore Docs.

Embedded nRF52 bootloader update

An opt-in Repeater or Room Server build can carry its application firmware and the exact board's OTAFIX 2.4.12 bootloader in one application image. Install that application first, then activate the bootloader replacement with an authenticated admin command. Booting the image does not flash the bootloader automatically.

This follows the internal-flash bridge in MeshEnvy firmware PR #2. The replacement stays inside the running application's verified image until Nordic's MBR copies it to the bootloader region. It needs no external staging storage and does not replace the SoftDevice or change the filesystem layout.

Build

From the repository root, replace TARGET with the exact OTA-enabled nRF52840 Repeater or Room Server target:

bash build.sh build-firmware TARGET --with-bootloader 2.4.12 \
  --firmware-version v1.18.0.1-halo-keymind-cascade-dev

For direct PlatformIO builds, the equivalent opt-in is:

MESHCORE_NRF52_EMBED_BOOTLOADER=2.4.12 pio run -e TARGET

The generator matches the board and storage to the 2.4.12 catalog and verifies the release asset before embedding only its 40 KiB bootloader region. Host validation covers all 23 published profiles, including SenseCAP Solar P1. P1 uses its exact SCAP_DFU identity and S140 v7 layout; XIAO's XIAO_DFU identity remains separate despite the shared USB board ID. Unsupported profiles are refused. The usual application, capacity and memory checks still apply: the resource adds 40 KiB plus update code, so some profiles will not fit. The build does not remove features or shrink the filesystem to make room.

Opt-in outputs include -with-bootloader-2.4.12 in their names. Ordinary builds and their output names stay unchanged. The embedded image remains an application UF2/DFU package, not a combined SoftDevice/bootloader DFU package.

An installed bootloader with valid compatible identity metadata must match the candidate's board and runtime layout. For the explicitly qualified legacy RAK4631 transition, also supply the exact installed bootloader image:

MESHCORE_NRF52_LEGACY_BOOTLOADER=/absolute/path/full.hex \
  bash build.sh build-firmware RAK_4631_repeater --with-bootloader 2.4.12

The legacy exception binds the entire padded bootloader region by SHA-256. It accepts the qualified MeshEnvy 0.9.2-ev1 RAK4631 image, whose full-region SHA-256 is 64bfe69d56eefc2d0fe51770902aff70ea0cc06cad261d3d219e4a3c0efac8dc. A matching version string alone is insufficient; another board's image or an unknown stock bootloader is not accepted by that exception.

A P1 already running a XIAO bootloader needs a deliberate identity migration; the embedded installer does not change one board identity into another. Use the documented temporary recovery bridge for the installed identity, followed by the normal P1 bootloader. The all-in-one P1 variant embeds the normal 2.4.12 P1 image, not a recovery image.

Install and activate

1. Install the application through its normal USB UF2 or serial/Bluetooth DFU route. LoRa delivery requires an already working, compatible application OTA updater. An internal-only legacy receiver needs a delta from its exact installed application; this image does not give a stock bootloader its first LoRa update capability.

2. After the new application is running, use the local CLI or authenticated remote admin CLI:

   ota bootloader embedded status
   ota bootloader embedded audit
   ota bootloader embedded install HASH16
   

   Replace HASH16 with the image confirmation shown by status. Save the audit before installation. The acknowledgment means armed; replacement waits for the reply and queued/in-flight radio transmissions to drain.

3. After reboot, check get bootloader.ver and repeat the audit. Confirm 2.4.12 and compare the application, filesystem, settings and SoftDevice hashes. Check status before repeating a command whose reply was lost.

The bridge validates the live application, candidate hash, installed identity, chip/layout, MBR addresses, watchdog and flash protection before copying. A protected region is refused; the bridge does not unlock it. Existing staged ota bootloader status and ota bootloader install MID8 HASH16 commands keep their separate signed-package behavior. See bootloader updates over LoRa for that path.

Qualification

The source PR documents one successful RAK4631 migration with unchanged application, filesystem, settings and SoftDevice hashes. Its later guards have host checks, but the recorded hardware run predates the final PR build. Other boards and power-cut recovery are not hardware-qualified by that test. Keep local recovery access when qualifying a new transition; an older loader's initial application-delta stage may itself be destructive. The MBR parameter page is intentionally used during the bootloader copy and is outside the unchanged-settings claim.