Files
MeshCore/variants/station_g3_esp32/platformio.ini
T

460 lines
14 KiB
INI

; Both Station_G3_ESP32 and its legacy _r2 recipes now detect the populated SX1262
; daughterboard slot at boot. "r2" historically meant physical slot 2, not revision 2.
; Keep both environment names/identities for explicit builds and existing tooling;
; future bulk releases need only one image per role/profile. The pin flags below
; provide constructor defaults only; runtime discovery binds every radio GPIO.
; CLI: get/set radio.slot auto|1|2 (saved, reboot required). This physical selector
; is unrelated to the time-shared radio2 PHY profile.
[Station_G3_ESP32_common]
extends = esp32_base
board = station-g3-esp32
board_build.partitions = default_16MB.csv
build_flags =
${esp32_base.build_flags}
${sensor_base.build_flags}
-I variants/station_g3_esp32
-I src/helpers/ui
-D STATION_G3_ESP32
-D USE_SX1262
-D RADIO_CLASS=CustomSX1262
-D WRAPPER_CLASS=CustomSX1262Wrapper
-D P_PA1_EN=9 ; PA PL1 Mode: LOW/open selects low level, HIGH/short selects high level.
-D P_PA1_EN_ACTIVE=HIGH
-D LORA_TX_POWER=7 ; SX1262 input power to the Station G3 PA; final output depends on PA PL1/PL2 level.
-D MAX_LORA_TX_POWER=22
; -D P_LORA_TX_LED=35
-D PIN_BOARD_SDA=5
-D PIN_BOARD_SCL=6
-D PIN_USER_BTN=38
-D MOMENTARY_BUTTON_WAKE_FROM_SLEEP=1
-D MOMENTARY_BUTTON_WAKE_HOLD_MS=120000UL
-D PIN_GPS_RX=15
-D PIN_GPS_TX=7
-D SX126X_DIO2_AS_RF_SWITCH=true
-D SX126X_DIO3_TCXO_VOLTAGE=1.8
-D SX126X_CURRENT_LIMIT=140
-D SX126X_RX_BOOSTED_GAIN=0
-D DISPLAY_CLASS=SH1106Display
build_src_filter = ${esp32_base.build_src_filter}
+<../variants/station_g3_esp32>
+<helpers/sensors>
+<helpers/ui/SH1106Display.cpp>
+<helpers/ui/MomentaryButton.cpp>
lib_deps =
${esp32_base.lib_deps}
${sensor_base.lib_deps}
adafruit/Adafruit SH110X @ ~2.1.13
adafruit/Adafruit GFX Library @ ^1.12.1
; PA PL1 is one board-level jumper shared by both slots, so P_PA1_EN stays in the base above.
[station_g3_esp32_r1_pins]
build_flags =
-D P_LORA_DIO_1=48
-D P_LORA_NSS=11
-D P_LORA_RESET=21
-D P_LORA_BUSY=47
-D P_LORA_SCLK=12
-D P_LORA_MISO=14
-D P_LORA_MOSI=13
-D P_PRIMARY_LNA_EN=10 ; Primary Slot LNA Mode: LOW/open is LNA on, HIGH/short is LNA off.
-D P_PRIMARY_LNA_EN_ACTIVE=LOW
; Legacy slot-2 constructor defaults ("LNA S"); FEM control uses runtime slot pins.
[station_g3_esp32_r2_pins]
build_flags =
-D P_LORA_DIO_1=2
-D P_LORA_NSS=43
-D P_LORA_RESET=44
-D P_LORA_BUSY=1
-D P_LORA_SCLK=39
-D P_LORA_MISO=41
-D P_LORA_MOSI=40
-D P_PRIMARY_LNA_EN=42 ; Secondary Slot LNA Mode, same polarity as the primary slot.
-D P_PRIMARY_LNA_EN_ACTIVE=LOW
[Station_G3_ESP32]
extends = Station_G3_ESP32_common
build_flags =
${Station_G3_ESP32_common.build_flags}
${station_g3_esp32_r1_pins.build_flags}
build_src_filter = ${Station_G3_ESP32_common.build_src_filter}
lib_deps = ${Station_G3_ESP32_common.lib_deps}
[Station_G3_ESP32_r2]
extends = Station_G3_ESP32_common
build_flags =
${Station_G3_ESP32_common.build_flags}
${station_g3_esp32_r2_pins.build_flags}
build_src_filter = ${Station_G3_ESP32_common.build_src_filter}
lib_deps = ${Station_G3_ESP32_common.lib_deps}
[env:Station_G3_ESP32_repeater]
extends = Station_G3_ESP32
build_flags =
${Station_G3_ESP32.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<../examples/simple_repeater>
lib_deps =
${Station_G3_ESP32.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_logging_repeater]
extends = Station_G3_ESP32
build_flags =
${Station_G3_ESP32.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Logging Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<../examples/simple_repeater>
lib_deps =
${Station_G3_ESP32.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_room_server]
extends = Station_G3_ESP32
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<../examples/simple_room_server>
build_flags =
${Station_G3_ESP32.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Room"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
lib_deps =
${Station_G3_ESP32.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_sensor]
extends = Station_G3_ESP32
build_flags =
${Station_G3_ESP32.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Sensor"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<../examples/simple_sensor>
lib_deps =
${Station_G3_ESP32.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_companion_radio_usb]
extends = Station_G3_ESP32
build_flags =
${Station_G3_ESP32.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D ENABLE_USB_INTERFACE
; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1
; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${Station_G3_ESP32.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:Station_G3_ESP32_companion_radio_ble]
extends = Station_G3_ESP32
build_flags =
${Station_G3_ESP32.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D BLE_PIN_CODE=123456
-D BLE_DEBUG_LOGGING=1
-D OFFLINE_QUEUE_SIZE=512
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${Station_G3_ESP32.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:Station_G3_ESP32_companion_radio_wifi]
extends = Station_G3_ESP32
build_flags =
${Station_G3_ESP32.build_flags}
-I examples/companion_radio/ui-new
-D ENABLE_WIFI_INTERFACE
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D WIFI_DEBUG_LOGGING=1
-D WIFI_SSID='"myssid"'
-D WIFI_PWD='"mypwd"'
-D OFFLINE_QUEUE_SIZE=512
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<helpers/esp32/*.cpp>
+<helpers/wifi/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${Station_G3_ESP32.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:Station_G3_ESP32_companion_radio_full]
extends = env:Station_G3_ESP32_companion_radio_wifi
board_build.flash_mode = ${esp32_s3_full.board_build.flash_mode}
build_flags =
${env:Station_G3_ESP32_companion_radio_wifi.build_flags}
-D MESHCORE_REQUIRES_COMPANION_RADIO_FULL=1
[env:Station_G3_ESP32_kiss_modem]
extends = Station_G3_ESP32
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<../examples/kiss_modem/>
build_flags =
${Station_G3_ESP32.build_flags}
; KISS profile switching is performed locally by the SX1262 scanner, not
; through serial host round trips. Keep this fast-RX/buffered-SPI opt-in
; isolated to the host-powered modem image.
-D MC_SX1262_FAST_PROFILE_SWITCH=1
-D MC_SX1262_FAST_FS=1
-D MC_SX1262_FAST_PACKET_CACHE=1
-D MC_SX1262_BUFFERED_RADIO_HAL=1
-D MC_SX1262_SPI_HZ=8000000
[env:Station_G3_ESP32_repeater_observer_mqtt]
extends = Station_G3_ESP32
board_build.partitions = default_16MB.csv ; standard 16MB partition table
extra_scripts =
${esp32_base.extra_scripts}
pre:scripts/generate_cert_bundle.py
board_ssl_cert_source = adafruit-full
board_build.embed_files = src/certs/x509_crt_bundle.bin
build_flags =
${Station_G3_ESP32.build_flags}
-D ADVERT_NAME='"MQTT Observer"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D WITH_MQTT_BRIDGE=1
-D MQTT_MAX_PACKET_SIZE=1024
-D MQTT_DEBUG=1
# -D MESH_PACKET_LOGGING=1
# -D MESH_DEBUG=1
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
-D ESP32_CPU_FREQ=160
-D WITH_SNMP=1
# -D WIFI_SSID='"ssid"'
# -D WIFI_PWD='"password"'
# -D MQTT_SERVER='"your-mqtt-broker.com"'
# -D MQTT_PORT=1883
# -D MQTT_USERNAME='"your-username"'
# -D MQTT_PASSWORD='"your-password"'
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<helpers/bridges/MQTTBridge.cpp>
+<helpers/MQTTMessageBuilder.cpp>
+<helpers/JWTHelper.cpp>
+<helpers/SNMPAgent.cpp>
+<helpers/ui/SH1106Display.cpp>
+<../examples/simple_repeater>
lib_deps =
${Station_G3_ESP32.lib_deps}
${esp32_ota.lib_deps}
elims/PsychicMqttClient@^0.2.4
bblanchon/ArduinoJson @ 7.4.3
arduino-libraries/NTPClient
JChristensen/Timezone
paulstoffregen/Time@1.6.1
0neblock/SNMP_Agent
[env:Station_G3_ESP32_room_server_observer_mqtt]
extends = Station_G3_ESP32
board_build.partitions = default_16MB.csv ; standard 16MB partition table
extra_scripts =
${esp32_base.extra_scripts}
pre:scripts/generate_cert_bundle.py
board_ssl_cert_source = adafruit-full
board_build.embed_files = src/certs/x509_crt_bundle.bin
build_flags =
${Station_G3_ESP32.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Room Observer"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
-D WITH_MQTT_BRIDGE=1
-D MAX_NEIGHBOURS=50
-D MQTT_MAX_PACKET_SIZE=1024
-D MQTT_DEBUG=1
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
-D ESP32_CPU_FREQ=160
-D WITH_SNMP=1
build_src_filter = ${Station_G3_ESP32.build_src_filter}
+<helpers/bridges/MQTTBridge.cpp>
+<helpers/MQTTMessageBuilder.cpp>
+<helpers/JWTHelper.cpp>
+<helpers/ui/SH1106Display.cpp>
+<helpers/SNMPAgent.cpp>
+<../examples/simple_room_server>
lib_deps =
${Station_G3_ESP32.lib_deps}
${esp32_ota.lib_deps}
elims/PsychicMqttClient@^0.2.4
bblanchon/ArduinoJson @ 7.4.3
arduino-libraries/NTPClient
JChristensen/Timezone
paulstoffregen/Time@1.6.1
0neblock/SNMP_Agent
[env:Station_G3_ESP32_r2_repeater]
extends = Station_G3_ESP32_r2
build_flags =
${Station_G3_ESP32_r2.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${Station_G3_ESP32_r2.build_src_filter}
+<../examples/simple_repeater>
lib_deps =
${Station_G3_ESP32_r2.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_r2_room_server]
extends = Station_G3_ESP32_r2
build_src_filter = ${Station_G3_ESP32_r2.build_src_filter}
+<../examples/simple_room_server>
build_flags =
${Station_G3_ESP32_r2.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Room"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
lib_deps =
${Station_G3_ESP32_r2.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_r2_sensor]
extends = Station_G3_ESP32_r2
build_flags =
${Station_G3_ESP32_r2.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Slot 2 Sensor"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
build_src_filter = ${Station_G3_ESP32_r2.build_src_filter}
+<../examples/simple_sensor>
lib_deps =
${Station_G3_ESP32_r2.lib_deps}
${esp32_ota.lib_deps}
[env:Station_G3_ESP32_r2_repeater_observer_mqtt]
extends = Station_G3_ESP32_r2
board_build.partitions = default_16MB.csv ; standard 16MB partition table
extra_scripts =
${esp32_base.extra_scripts}
pre:scripts/generate_cert_bundle.py
board_ssl_cert_source = adafruit-full
board_build.embed_files = src/certs/x509_crt_bundle.bin
build_flags =
${Station_G3_ESP32_r2.build_flags}
-D ADVERT_NAME='"MQTT Observer"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D WITH_MQTT_BRIDGE=1
-D MQTT_MAX_PACKET_SIZE=1024
-D MQTT_DEBUG=1
# -D MESH_PACKET_LOGGING=1
# -D MESH_DEBUG=1
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
-D ESP32_CPU_FREQ=160
-D WITH_SNMP=1
# -D WIFI_SSID='"ssid"'
# -D WIFI_PWD='"password"'
# -D MQTT_SERVER='"your-mqtt-broker.com"'
# -D MQTT_PORT=1883
# -D MQTT_USERNAME='"your-username"'
# -D MQTT_PASSWORD='"your-password"'
build_src_filter = ${Station_G3_ESP32_r2.build_src_filter}
+<helpers/bridges/MQTTBridge.cpp>
+<helpers/MQTTMessageBuilder.cpp>
+<helpers/JWTHelper.cpp>
+<helpers/SNMPAgent.cpp>
+<helpers/ui/SH1106Display.cpp>
+<../examples/simple_repeater>
lib_deps =
${Station_G3_ESP32_r2.lib_deps}
${esp32_ota.lib_deps}
elims/PsychicMqttClient@^0.2.4
bblanchon/ArduinoJson @ 7.4.3
arduino-libraries/NTPClient
JChristensen/Timezone
paulstoffregen/Time@1.6.1
0neblock/SNMP_Agent
[env:Station_G3_ESP32_r2_room_server_observer_mqtt]
extends = Station_G3_ESP32_r2
board_build.partitions = default_16MB.csv ; standard 16MB partition table
extra_scripts =
${esp32_base.extra_scripts}
pre:scripts/generate_cert_bundle.py
board_ssl_cert_source = adafruit-full
board_build.embed_files = src/certs/x509_crt_bundle.bin
build_flags =
${Station_G3_ESP32_r2.build_flags}
-D ADVERT_NAME='"Station G3 ESP32 Room Observer"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
-D WITH_MQTT_BRIDGE=1
-D MAX_NEIGHBOURS=50
-D MQTT_MAX_PACKET_SIZE=1024
-D MQTT_DEBUG=1
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
-D CONFIG_MBEDTLS_CERTIFICATE_BUNDLE=y
-D ESP32_CPU_FREQ=160
-D WITH_SNMP=1
build_src_filter = ${Station_G3_ESP32_r2.build_src_filter}
+<helpers/bridges/MQTTBridge.cpp>
+<helpers/MQTTMessageBuilder.cpp>
+<helpers/JWTHelper.cpp>
+<helpers/ui/SH1106Display.cpp>
+<helpers/SNMPAgent.cpp>
+<../examples/simple_room_server>
lib_deps =
${Station_G3_ESP32_r2.lib_deps}
${esp32_ota.lib_deps}
elims/PsychicMqttClient@^0.2.4
bblanchon/ArduinoJson @ 7.4.3
arduino-libraries/NTPClient
JChristensen/Timezone
paulstoffregen/Time@1.6.1
0neblock/SNMP_Agent