rich/MeshCore
1
0 Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
keymindCascade
MeshCore/variants/rak3401/platformio.ini
T

248 lines
8.3 KiB
INI
Raw Permalink Blame History

[rak3401]
extends = nrf52_base
board = rak3401
board_check = true
board_build.ldscript = boards/nrf52840_s140_v6.ld
extra_scripts = ${nrf52_base.extra_scripts}
post:variants/rak3401/fix_bsec_lib.py
build_flags = ${nrf52_base.build_flags}
${sensor_base.build_flags}
-I variants/rak3401
-D RAK_3401
-D RAK_BOARD
-D RECOVERABLE_EXTERNAL_RADIO
; RAK13300/RAK13302 BUSY and DIO1 use nRF52840 P0.09/P0.10. A full
; chip erase restores those pads to NFC mode, so SystemInit must repair
; UICR and reset once before the external SX1262 can be reached.
-D CONFIG_NFCT_PINS_AS_GPIOS
-D NRF52_POWER_MANAGEMENT
-D RADIO_CLASS=CustomSX1262
-D WRAPPER_CLASS=CustomSX1262Wrapper
-D LORA_TX_POWER=22
-D SX126X_CURRENT_LIMIT=140
-D SX126X_RX_BOOSTED_GAIN=1
-D SX126X_REGISTER_PATCH=1 ; Patch register 0x8B5 for improved RX with SKY66122 FEM
; WB_IO2 also powers the radio frontend: its immutable rail hold stays HIGH.
; GPS may stop parsing, but it must never remove this shared radio supply.
-D PIN_GPS_EN=-1 ; -1 = no dedicated GPS enable pin (power is the shared 3V3_S rail), same as rak4631
-UENV_INCLUDE_BME680
-D ENV_INCLUDE_BME680_BSEC=1
build_src_filter = ${nrf52_base.build_src_filter}
+<../variants/rak3401>
+<helpers/sensors>
+<helpers/ui/SSD1306Display.cpp>
+<helpers/ui/MomentaryButton.cpp>
lib_deps =
${nrf52_base.lib_deps}
${sensor_base.lib_deps}
adafruit/Adafruit SSD1306 @ ^2.5.13
sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27
boschsensortec/BSEC Software Library @ ^1.8.1492
[env:RAK_3401_repeater]
extends = rak3401
extra_scripts = ${nrf52_lora_ota.extra_scripts}
post:variants/rak3401/fix_bsec_lib.py
build_flags =
${rak3401.build_flags}
-UENABLE_OTA
-D DISABLE_LORA_OTA=1 ; Full external-sensor build exceeds the in-place OTA ceiling
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"RAK3401 1W Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
;-D MESH_PACKET_LOGGING=1
;-D MESH_DEBUG=1
build_src_filter = ${rak3401.build_src_filter}
+<helpers/ota/*.cpp>
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
; Explicit lean alternative to the full-sensor, non-OTA repeater above. It removes optional
; environmental telemetry sensors while retaining the common INA I2C voltage/current monitors,
; board display/RTC support, and both RAK12500 I2C and RAK12501 UART GPS paths. Use sensor slot A:
; slot D conflicts with the RAK13302 radio's BUSY/DIO1 wiring.
; RAK12500 and the configured INA3221 both use I2C address 0x42, so they cannot be installed
; together at those addresses. Keep GPS at 0x42, strap INA3221 A0 to SCL for 0x43, and build
; with -DTELEM_INA3221_ADDRESS=0x43 when both modules are required.
; The legacy target name remains stable for OTA compatibility.
[env:RAK_3401_repeater_lora_ota_no_external_sensors]
extends = rak3401
extra_scripts = ${nrf52_lora_ota.extra_scripts}
post:variants/rak3401/fix_bsec_lib.py
build_flags =
${rak3401.build_flags}
${nrf52_reduced_sensors_keep_ina_gps.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"RAK3401 1W Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D ENABLE_OTA=1
-D OTA_FLASH_STORE=1
-D OTA_FOLDER_SERIAL
-D OTA_TARGET_NAME_TABLE=0 ; IDs remain authoritative; omit the 540-entry display-name table
-D OTA_LOCAL_TARGET_ID=0x2fa509c1
-D OTA_LOCAL_TARGET_NAME='"RAK_3401_repeater_lora_ota_no_external_sensors"'
-D OTA_FETCH_PIPELINE=4 ; adaptive one-packet flights grow 1 -> 2 -> 3 -> 4 on a clean link
build_src_filter = ${rak3401.build_src_filter}
+<helpers/ota/*.cpp>
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
lib_deps =
${nrf52_lora_ota.lib_deps}
${nrf52_reduced_sensors_keep_ina_gps.lib_deps}
adafruit/Adafruit SSD1306 @ ^2.5.13
sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27
; Full-sensor/GPS repeater with RAK13302 1 W radio and an exact 2 MiB Winbond
; W25Q16JV breakout. The flash shares SCK/MOSI/MISO with the RAK13302 but uses
; its own CS on J11 AIN1. The QSPI store temporarily releases and restores SPI1
; while holding the radio NSS high. GPS remains supported in sensor slot A.
[env:RAK_3401_repeater_rak13302_w25q16_lora_ota]
extends = rak3401
extra_scripts = ${nrf52_lora_ota.extra_scripts}
post:variants/rak3401/fix_bsec_lib.py
build_flags =
${rak3401.build_flags}
${nrf52_wisblock_w25q16_ota.build_flags}
-D OTA_QSPI_RAK3401_RADIO_BUS_HANDOFF=1
-D MOTA_HW_ID='"RAK3401_RAK13302_W25Q16"'
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"RAK3401 1W + W25Q16 OTA"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D ENABLE_OTA=1
-D OTA_FOLDER_SERIAL
-D OTA_FETCH_PIPELINE=4
build_src_filter = ${rak3401.build_src_filter}
+<helpers/ota/*.cpp>
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
; One full-sensor repeater image for internal flash or the separate-CS W25Q16.
; RAK15001 cannot be selected: it shares the RAK13302 radio chip-select.
[env:RAK_3401_repeater_unified_lora_ota]
extends = rak3401
extra_scripts = ${nrf52_lora_ota.extra_scripts}
post:variants/rak3401/fix_bsec_lib.py
build_flags =
${rak3401.build_flags}
${nrf52_wisblock_auto_ota.build_flags}
-D OTA_QSPI_RAK3401_RADIO_BUS_HANDOFF=1
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"RAK3401 1W Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D ENABLE_OTA=1
-D OTA_FOLDER_SERIAL
-D OTA_TARGET_NAME_TABLE=0
-D OTA_FETCH_PIPELINE=4
build_src_filter = ${rak3401.build_src_filter}
+<helpers/ota/*.cpp>
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
[env:RAK_3401_room_server]
extends = rak3401
build_flags =
${rak3401.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"Test Room"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
;-D MESH_PACKET_LOGGING=1
;-D MESH_DEBUG=1
build_src_filter = ${rak3401.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_room_server>
[env:RAK_3401_companion_radio_usb]
extends = rak3401
board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld
board_upload.maximum_size = 712704
build_flags =
${rak3401.build_flags}
-I examples/companion_radio/ui-new
-D PIN_USER_BTN_ANA=31
-D DISPLAY_CLASS=SSD1306Display
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D ENABLE_USB_INTERFACE
; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1
; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1
build_src_filter = ${rak3401.build_src_filter}
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${rak3401.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:RAK_3401_companion_radio_ble]
extends = rak3401
board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld
board_upload.maximum_size = 712704
build_flags =
${rak3401.build_flags}
-I examples/companion_radio/ui-new
-D PIN_USER_BTN_ANA=31
-D DISPLAY_CLASS=SSD1306Display
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D BLE_PIN_CODE=123456
-D BLE_DEBUG_LOGGING=1
-D OFFLINE_QUEUE_SIZE=256
;-D MESH_PACKET_LOGGING=1
;-D MESH_DEBUG=1
build_src_filter = ${rak3401.build_src_filter}
+<helpers/nrf52/SerialBLEInterface.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${rak3401.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:RAK_3401_terminal_chat]
extends = rak3401
build_flags =
${rak3401.build_flags}
-D MAX_CONTACTS=100
-D MAX_GROUP_CHANNELS=1
;-D MESH_PACKET_LOGGING=1
;-D MESH_DEBUG=1
build_src_filter = ${rak3401.build_src_filter}
+<../examples/simple_secure_chat/main.cpp>
lib_deps =
${rak3401.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:RAK_3401_sensor]
extends = rak3401
build_flags =
${rak3401.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"RAK3401 Sensor"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D USER_GPIO_CONTROL=1
;-D MESH_PACKET_LOGGING=1
;-D MESH_DEBUG=1
build_src_filter = ${rak3401.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_sensor>
[env:RAK_3401_kiss_modem]
extends = rak3401
build_src_filter = ${rak3401.build_src_filter}
+<../examples/kiss_modem/>
Reference in new issue View Git Blame Copy Permalink