Files
mikecarper a3d77a9a76 Clean project references and separate optional bench tooling
Remove unrelated ecosystem comparisons and software citations while retaining hardware links, measured model names, and required license notices.

Preserve stock-peer runners and tests in a verified local validation package. Keep shared Companion USB transport in the firmware repository for the raw-radio sweep and OTA seeder, with focused CI coverage. Restore missing hosted documentation links.
2026-10-21 17:35:37 -07:00

140 lines
5.0 KiB
C

/*
* variant.h - Seeed SenseCAP MeshTracker X1 (nRF52840 + Semtech LR2021)
*/
#pragma once
#include "WVariant.h"
////////////////////////////////////////////////////////////////////////////////
// Low frequency clock source
#define USE_LFXO // 32.768 kHz crystal oscillator
#define VARIANT_MCK (64000000ul)
////////////////////////////////////////////////////////////////////////////////
// Power
#define NRF_APM // detect usb power
#define PIN_3V3_EN (39) // P1.7 Power to sensors
#define PIN_BAT_ADC_EN (38) // P1.6 Power to battery ADC divider
#define PIN_RTC_EN (9) // P0.9 Power to RTC
#define BATTERY_PIN (2) // P0.2/AIN0
#define BATTERY_IMMUTABLE
#define ADC_MULTIPLIER (2.0F)
#define EXT_CHRG_DETECT (35) // P1.3, LOW while charging
// P1.4 is the charger's second status line, but it reads LOW regardless of
// charge state on this board, so it is not used.
#define EXT_PWR_DETECT (5) // P0.5
#define ADC_RESOLUTION (14)
#define BATTERY_SENSE_RES (12)
#define AREF_VOLTAGE (3.0)
////////////////////////////////////////////////////////////////////////////////
// Number of pins
#define PINS_COUNT (48)
#define NUM_DIGITAL_PINS (48)
#define NUM_ANALOG_INPUTS (6)
#define NUM_ANALOG_OUTPUTS (0)
////////////////////////////////////////////////////////////////////////////////
// UART pin definition
#define PIN_SERIAL1_RX (14) // P0.14 (GPS)
#define PIN_SERIAL1_TX (13) // P0.13 (GPS)
#define PIN_SERIAL2_RX (17) // P0.17
#define PIN_SERIAL2_TX (16) // P0.16
////////////////////////////////////////////////////////////////////////////////
// I2C pin definition
#define HAS_WIRE (1)
#define WIRE_INTERFACES_COUNT (1)
#define PIN_WIRE_SDA (47) // P1.15
#define PIN_WIRE_SCL (46) // P1.14
#define I2C_NO_RESCAN
////////////////////////////////////////////////////////////////////////////////
// SPI pin definition
#define SPI_INTERFACES_COUNT (1)
#define PIN_SPI_MISO (40) // P1.8
#define PIN_SPI_MOSI (41) // P1.9
#define PIN_SPI_SCK (11) // P0.11
#define PIN_SPI_NSS (12) // P0.12
////////////////////////////////////////////////////////////////////////////////
// Builtin LEDs (RGB)
#define LED_BUILTIN (-1)
#define LED_RED (3) // P0.3
#define LED_GREEN (24) // P0.24
#define LED_BLUE (28) // P0.28
#define LED_PIN LED_GREEN
#define LED_STATE_ON HIGH
////////////////////////////////////////////////////////////////////////////////
// Builtin buttons
#define PIN_BUTTON1 (6) // P0.6, active HIGH (internal pull-down)
#define BUTTON_PIN PIN_BUTTON1
////////////////////////////////////////////////////////////////////////////////
// LR2021
#define LORA_DIO_1 (33) // P1.1, IRQ line (LR2021 DIO8)
#define LORA_NSS (PIN_SPI_NSS) // P0.12
#define LORA_RESET (42) // P1.10
#define LORA_BUSY (7) // P0.7
#define LORA_SCLK (PIN_SPI_SCK) // P0.11
#define LORA_MISO (PIN_SPI_MISO) // P1.8
#define LORA_MOSI (PIN_SPI_MOSI) // P1.9
////////////////////////////////////////////////////////////////////////////////
// GPS (Airoha, dual-band L1+L5)
#define HAS_GPS 1
#define GPS_RX_PIN PIN_SERIAL1_RX
#define GPS_TX_PIN PIN_SERIAL1_TX
#define GPS_BAUD_RATE (115200)
#define GPS_EN (43) // P1.11, active HIGH
#define GPS_RESET (8) // P0.8, active HIGH
#define GPS_VRTC_EN (45) // P1.13
#define GPS_SLEEP_INT (30) // P0.30
#define GPS_RTC_INT (29) // P0.29
////////////////////////////////////////////////////////////////////////////////
// Haptic driver (DRV2605 on I2C)
#define PIN_DRV_EN (37) // P1.5, power to haptic driver
////////////////////////////////////////////////////////////////////////////////
// Buzzer
#define BUZZER_PIN (25) // P0.25, pwm output
////////////////////////////////////////////////////////////////////////////////
// QSPI Flash
#define PIN_FLASH_EN (15) // P0.15 (Flash power enable)
#define PIN_QSPI_SCK (19) // P0.19
#define PIN_QSPI_CS (20) // P0.20
#define PIN_QSPI_IO0 (21) // P0.21
#define PIN_QSPI_IO1 (22) // P0.22
#define PIN_QSPI_IO2 (23) // P0.23
#define PIN_QSPI_IO3 (32) // P1.00
#define EXTERNAL_FLASH_DEVICES GD25Q64C