Add selectable shared ESP-NOW channels, raw/wrapped bridge compatibility, and bounded fragmentation for maximum-size packets.\n\nGive ESP32 Full profiles WiFi coexistence, stabilize WebConfig and USB terminal lifecycles, and keep disabled bridges stopped during observer updates.\n\nUpdate generated UI, firmware selection, documentation, and regression coverage.
Replace the sparse Heltec V4 R8 observer home screen with a padded dark
analytics dashboard, add manual display control, and make blanking a runtime
setting.
Dashboard (DISPLAY_ACTIVITY_DASHBOARD, the four R8 TFT observer envs):
- RadioActivityWindow: 20 one-minute buckets of valid RX packets, no heap.
The caller's 32-bit millis() is extended to a monotonic 64-bit clock, so
nothing downstream has a rollover case; an always-on node passes 2^32 ms
after ~49.7 days, which would otherwise re-enter warm-up and divide 20
minutes of traffic by seconds. Rates use 19 whole minutes plus the elapsed
part of the current one rather than a fixed 1200 s.
- ObserverDashboard: header, radio strip, headline totals, a 20-bar
packets-per-minute graph and RF/status footers, with separate portrait and
landscape layouts. A text row is a fixed 16 px, which is 3.2 logical units
in portrait but 4.27 in landscape, so one shared grid would overlap.
Text is trimmed by character budget, not measured width: getTextWidth()
reports an over-long string at the portrait driver's fallback scale, so
DisplayDriver::drawTextEllipsized() under-trims and the row renders at half
height.
- Six per-row signatures computed from what is actually drawn, so only the
rows whose pixels changed repaint. No startFrame(), no whole-screen clear.
Link state moved out of the full-frame signature, so a DHCP renewal or WiFi
flap repaints one footer row instead of the panel.
- Dark theme by retuning the UIColor statics at runtime, which needs no
display-driver edit and carries boot, setup, reboot and power-off with it.
Touch and button (DISPLAY_TOUCH_TOGGLE):
- CHSC6X at I2C 0x2E, polled; TP_INT is unusable (optional R13, and GPIO 43
is U0TXD). The point-count byte is tested against a valid count, never
against non-zero: an idle read returns 0xFF, which reads as a finger held
down forever and latches the tap detector after one event.
- turnOff() no longer parks PIN_TFT_RST low on this board. GPIO 21 is a
shared LCD_RST/TP_RST net, so doing that held the touch controller in
reset for as long as the display was off. Verified against Heltec's
expansion-board and mainboard schematics and the V4-R8 datasheet pinout,
which also correct the pin comment in HeltecV4R8Board.cpp.
- The USER button click now toggles the display too; it previously did
nothing whenever the display was already on.
display.timeout:
- `set display.timeout <secs>` / `get display.timeout`, 0 = stay on, 60 s
default, 3600 max. Read live, so a change applies without a reboot and
restarts the countdown rather than firing on the old deadline.
- Stored in MQTTPrefs (/mqtt.json), keeping NodePrefs aligned with upstream.
Runtime-only: LegacyV1MQTTPrefs and the four frozen binary payload sizes
are unchanged. No JSON format-version bump - the loader skips keys no
def() claims, so older firmware reads newer files and this firmware reads
older ones with the default applied. Both directions are covered by tests.
- Joins the observer atomic-setter contract, so a failed save rolls the live
value back instead of only claiming to.
New periodic work uses a wrap-safe deadline check; `millis() >= deadline`
fires every loop for a whole interval before each rollover.
Adds test_radio_activity_window, test_observer_dashboard (driving the real
renderer against a recording DisplayDriver in both orientation profiles) and
test_touch_tap_detector. 440 native cases pass.
Add the framed BLE mOTA transport and companion control path, complete the full-profile build and runtime fixes, and document and test the OTA workflow.
Expose the Full Companion terminal over TCP and add an authenticated, replay-resistant host command service with documented CPU temperature, reboot, and allowlisted program examples.\n\nImprove LoRa OTA diagnostics and persistent CLI handling, reduce clock correction drift to ten minutes, and make mOTA stream flush behavior an explicit transport policy with regression coverage.
Picks up upstream MeshCore 1.17.1.
Notable upstream content:
- 1.17.1 version/build-date bump in the example MyMesh headers.
- nRF52: combine radio entropy with CC310 RNG.
- Companion FEM prefs: load/save of fem_ properties commented out until they
can be set from the client.
- Scoped reply routing: replies no longer dropped when flood.max.unscoped is
low (RoutingPolicy + unit tests).
- nRF52 unused-pin sweep (T1, T-Echo Lite, MeshPocket).
No conflicts.
Brings in the external FEM gain preferences (fem_txgain, PR #3137 plus the
companion-side port), the AGC reset rxgain fix, the LR2021 preamble/IRQ
timeout logic, and assorted variant fixes (T096, T-Echo Card TCXO, promicro
pinmap, minewsemi, R1 Neo).
Conflict resolutions:
- SH1106Display: both sides fixed T-Beam Supreme startup independently. Kept
our _initialized guard and DISPLAY_ADDRESS_ALT override, took upstream's
SA0-pair fallback and its unconditional display.begin() so the frame buffer
is allocated even when no panel answers.
- MyMesh/SensorMesh/CommonCLI: took upstream's fem_txgain default and wiring,
kept our comments and the observer-side prefs layout.
Also fixes CustomLLCC68Wrapper, which upstream missed when sx126xResetAGC
gained its rx_boost_gain parameter. No variant builds that wrapper today, so
neither tree failed to compile.
Picks up upstream MeshCore 1.17.0 and the dev commits that followed it.
Notable upstream content:
- 1.17.0 version/build-date bump in the example MyMesh headers.
- anon_req hardening: reply_path_len is now uint8_t with an isValidPathLen()
bounds check and a 0xFF sentinel; reply_path_hash_size is gone.
- LR2021 support (Meshnology W12, Seeed MeshTracker X1) incl. side detectors,
multi-SF and the new `extra.sf` get/set CLI.
- CustomLFS 0.2.2 -> 0.2.3 (GD25Q64C support).
- kiss_modem envs for several nRF52 variants; ThinkNode M6 GPS/flash fixes.
Conflicts resolved:
- platformio.ini: took upstream's CustomLFS 0.2.3, kept our lib_ignore for
the vendored PsychicMqttClient.
- CommonCLI.h: kept both upstream's USE_LR2021 configSideDetectors() hook and
our fault-alert callbacks.
NodePrefs gains upstream's extra_sf[4], which is not registered with
ConfigSerializer, so /prefs.json layout is unchanged.
Verified: 275/275 native host tests pass; Heltec_v3_repeater_observer_mqtt,
Heltec_v3_repeater and heltec_v4_repeater_observer_mqtt all build.
The full embedded string is v1.16.0.5-observer-beta-dev-a1b2c3d. The -observer
tag is on every observer build and the commit is for machines, so neither tells
a person anything at a glance. Both the page header and the console banner now
show base + published build number + channel, paired with the build date the
way `ver` pairs them:
v1.16.0.5-dev (6 Jun 2026)
v1.16.0.5 (6 Jun 2026)
`ver` still prints the whole string, commit included, for when that is what you
need. The channel suffix follows the release filenames rather than the embedded
tag — build.sh writes FILENAME_CHANNEL_TAG "-dev" for the same builds it tags
"-observer-beta-dev" internally, so "-dev" is the name these already carry.
Carrying the build date meant /api/status had to report it; WebConfigServer now
takes FIRMWARE_BUILD_DATE alongside FIRMWARE_VERSION, from the same defines
`ver` reads.
A local build has neither build number nor channel to show, so the fact worth
knowing about it moves to the second line: "local build, OTA not configured".
build.sh deliberately leaves OTA_MANIFEST_BASE undefined there, and a bare
version number gives no hint that the node cannot update itself.
Improve companion BLE delivery and idempotent remote CLI retries, make FPF7 persistence atomic with FPF6 migration, verify staged OTA data on resume, and clarify filter policy wildcard and BlackHole semantics.