If an `ota pull <#> folder` block-write fails mid-transfer (the motatool seeder
link dropped), the fetch enters a new PAUSED state instead of failing or falling
back to RAM/flash: progress stays on the host, the manager stops requesting, and
loop()/stall-detection leave it untouched (it waits indefinitely). On reconnect
the ESP32 seeder re-registers the folder destination and, if PAUSED, calls
resumeStaged(): OP_STAT re-attaches the host's partial, the leaves are re-read,
and only the missing blocks are re-requested (a brand-new/absent file restarts
from 0). `ota status` reports the paused state.
FolderMotaStore: an OtaStore that streams an in-transit .mota straight to the host
folder over the seeder link (OP_BEGIN/WRITE/SREAD/STAT/FIN) instead of RAM/flash —
the device holds no local staging for it. Wired as a selectable pull destination:
- OtaContext gains a folder_dest (registered by the app while a motatool `serve`
link is up) + its human id (e.g. "tcp 192.168.4.5").
- `ota pull <#> <dest>` now takes a MANDATORY destination; `ota pull <#>` with none
lists the choices (flash always; folder + its link id when connected).
- The ESP32 WiFi seeder registers/clears the folder destination on connect/close —
the same connection both serves the folder and accepts pulls into it.
Captures an exact copy of a device's firmware over the mesh to build a delta
against. Pause/resume on a mid-pull disconnect follows.
The discovery beacon previously re-announced at a random 3-10 min interval.
Replace that with a fixed, user-configurable cadence:
- OtaManager::advert_mins() — re-advertise every N minutes after the boot
burst; 0 disables periodic re-advertise (boot burst only). Default 24h.
- Persisted in NodePrefs (CommonCLI) and runtime-tunable: `ota config advert
<minutes>` (0..10080; 0 = off), and shown in `ota config`.
- When periodic advert is disabled, the scheduler still re-checks the config
on a slow timer, so a later `ota config advert <mins>` takes effect live.
Also advertise immediately whenever the served set changes — when a motatool
folder is attached to / detached from the ESP32 WiFi seeder — so peers learn
about newly-available firmware without waiting for the next interval (the
`ota folder` serial path already announced on attach).
Docs: protocol beacon-cadence note + user-guide `ota config advert`.
Extends the USB-serial folder relay to WiFi so an ESP32 companion can both
serve .mota and be operated headlessly:
- motatool `serve --tcp <host[:port]>`: a TcpTransport sibling of the serial
transport (default port 5001). SeederCore/Folder are reused unchanged — the
COUNT/DESCRIBE/READ protocol is transport-agnostic.
- ESP32 companion: a dedicated OTA seeder port (5001) for `serve --tcp`, plus
an OTA text console on 5002 (`nc <ip> 5002` -> `ota status|ls|announce|...`,
the same handle_ota_command CLI serial nodes have). Both run alongside the
phone-app port (5000); all three coexist.
- WiFi.setSleep(false): ESP32 STA mode's modem power-save periodically sleeps
the modem/CPU and stalls the SX1262 SPI+DIO servicing, leaving LoRa deaf
while WiFi is associated. Disabling it restores the radio (HW-validated:
a V3 WiFi companion is then discovered over LoRa and discovers its peers).
- docs: serving .mota over WiFi (protocol §10.2 + user guide).
Framework for upcoming variant-specific PRs that add LED feedback during boot. The hook gives users visual cues that the device is busy and
shouldn't be interacted with until startup completes.
The companion_radio example was not restoring the GPS enabled/disabled
preference from flash after reboot. The preference was being saved
correctly when toggled via the mobile app, but on boot,
sensors.begin() -> initBasicGPS() unconditionally sets gps_active=false
and nothing subsequently restored the persisted state.
Added applyGpsPrefs() (matching the pattern in simple_repeater,
simple_sensor, and simple_room_server) and call it from main.cpp
after sensors.begin() to ensure the GPS hardware is initialized
before the saved preference is applied.
Pulled the class out of main.cpp, made a header to go along with it, externed globals in headers to make them accessible to button code. Added button code to send an advert on double press. Refactored ini files to prevent linker errors.
mikecarper
Quency-D
Valentin Kivachuk Burda
Kevin Le
ripplebiz
AtlavoxDev
Rococo88
Alejandro Ramirez
Wessel Nieboer
taco
Scott Powell
Quency-D
Florent de Lamotte
hank
liamcottle
seagull9000