The `::init` method in the Adafruit ST7789 library is responsible to
initialize the device. This includes performing a reset, which can be
found in the Adafruit source for `Adafruit_SPITFT`.
Before this change, MeshCore performed its own ST7789 display reset
sequence, which consisted of three steps.
* Pull reset low
* Wait 10ms
* Pull reset high
Importantly, there was no fixed delay after pulling reset high. The
ST7789 driver requires a delay (T<sub>RT</sub>) of 5ms in Sleep In Mode
and 120ms in Sleep Out Mode before it will properly receive commands.
When `Adafruit_SPITFT` resets the device after MeshCore has already
reset it, the mandatory time may not have elapsed, leading to strange
behavior. In the author's case, this issue caused the initial
`fillScreen` to fail, such that the display showed an uninitialized
framebuffer.
This removes the MeshCore delay, leaving the responsibility of reset to
`Adafruit_SPITFT`, where they have the correct delays in place with
extra safety margin. The change was briefly tested by Josiah VanderZee
and Ben Zignego on a custom hardware build using an nRF52840 Dongle and
an Adafruit 4311 TFT display. The user button seemed to behave
strangely, but the display looked correct.
Introduced new PlatformIO environments for the LilyGo T-LoRa V2.1-1.6 board, including `LilyGo_TLora_V2_1_1_6_repeater_observer_mqtt` and `LilyGo_TLora_V2_1_1_6_room_server_observer_mqtt`. These environments optimize flash usage by omitting the `sensor_base` and include specific build flags and dependencies for enhanced MQTT capabilities. Updated documentation to reflect changes in partition table handling and NVS settings during firmware updates.
USE_LR1110 was missing from the preprocessor guard in CommonCLI.cpp,
causing both get and set to fail silently on T1000-E:
- get radio.rxgain returned the full radio config string (fell through
to the memcmp("radio", 5) branch)
- set radio.rxgain returned "unknown config" (no branch matched)
Fix: add -D USE_LR1110 to variants/t1000-e/platformio.ini and include
USE_LR1110 in the #if guard on both get and set branches.
CustomLR1110Wrapper already implements setRxBoostedGainMode() and
getRxBoostedGainMode() via the RadioLibWrapper virtual interface,
so no radio-layer changes are required.
Tested on T1000-E: get/set/persist all confirmed working.
Reorder login auth so that, in priority:
1. Admin password match -> ADMIN (overrides ACL — a region_mgr or
other ACL'd client who knows the admin pw can still upgrade).
2. Sender pubkey is in the ACL -> use the stored permissions
(no password required; pubkey is itself an identity assertion).
3. Guest password match (or blank pw when guest pw is unset) -> GUEST.
4. Otherwise -> reject.
Previously the ACL was consulted only when `data[0] == 0` (blank pw),
so a non-blank password would skip the ACL entirely and fall through
to the password block. Phones that sent any non-empty password field
— even a stale one — would never see their ACL-granted role; they'd
either be rejected or assigned the role implied by the password match.
Implementation is a single-line change: gate the ACL lookup on "the
admin pw did NOT match". When admin matches, we skip the lookup so
the existing password block sets ADMIN unconditionally (the right
behavior for the upgrade case). When admin does not match, the ACL
takes over; only on an ACL miss do we fall through to guest/reject.
Introduces a fourth ACL role (value 4) that can manage the region map
without full admin privileges. The role is intended for trusted users
who curate regions on a repeater but should not have access to general
admin commands.
ClientACL:
- Widen PERM_ACL_ROLE_MASK from 2 to 3 bits so the new value fits.
- Add PERM_ACL_REGION_MGR and ClientInfo::isRegionMgr().
- Exempt region_mgr entries from least-recently-active eviction in
putClient(), same as admins.
simple_repeater:
- Phones may still gate UI on the legacy is_admin byte (reply_data[6]),
so report region_mgr as admin there. Without this, the phone CLI
falls back to guest view.
- Allow region_mgr to send TXT_MSG CLI commands. handleCommand()
gates non-whitelisted commands with "Err - not permitted". The
whitelist covers region.* (read+write) plus a small set of
read-only queries (get, ver, board, neighbors, clock, sensor
get/list).
- Pass the ClientInfo* through to handleCommand and drop the
redundant sender_timestamp parameter (derived from
sender->last_timestamp; NULL means Serial CLI).
- Use ~PERM_ACL_ROLE_MASK instead of ~0x03 when clearing role bits
on login, so the wider mask is honored.
Increased the total number of built-in MQTT presets from 12 to 13 by adding the ColoradoMesh preset. This addition enhances the MQTT bridge's capabilities for connecting to more networks.
Liam Cottle
Kevin Le
ripplebiz
Kenneth Privitt
Josiah VanderZee
agessaman
Nick Le Mouton
jirogit
Avi0n
Rastislav Vysoky
Wessel Nieboer
Kyle
Quency-D
chrisdavis2110
hank
taco