Integrate compatible observer board, preset, WebConfig, display, CI, and policy updates. Preserve the checkout's newer MQTT binary preferences and WiFi bridge runtime where the forked implementations conflict. Keep ThinkNode observer networking WiFi-based until the Ethernet transport is wired into that runtime.
Add acknowledged SetFs and packet-cache shortcuts for SX1262, extend the LR1110 FS-mode fast path with buffered SPI, and keep the expander-backed Indicator on its previous path. Include HIL fixtures, validation notes, and regression tests.
The motherboard has two RF daughterboard slots on separate GPIOs, mirrored by
its "LNA P" / "LNA S" jumpers, but the variant only ever pinned slot 1.
The shared configuration moves into [Station_G3_ESP32_common], with the SPI and
LNA lines split into per-slot sections. [Station_G3_ESP32] (slot 1) and
[Station_G3_ESP32_r2] (slot 2) each compose common + their own pins, so neither
set of -D flags has to shadow the other on the compile line - appending an
override would work only by last-wins, and esp32_base's -w hides the resulting
redefinition warning. Every pre-existing env keeps its name and resolves to
byte-identical options; verified by diffing pio project config --json-output.
PA PL1 is one board-level jumper shared by both slots, so P_PA1_EN stays in the
common section along with the TX power calibration.
Adds r2 twins of the repeater, room server and both observer envs, each an exact
mirror of its slot-1 sibling apart from the base it extends.
Slot 2 pins come from on-hardware testing in agessaman/MeshCore#49 and are not
documented publicly; the vendor wiki serves no content to fetchers.
Known limitation, unchanged from that PR: GPIO 42 and 43 fall outside the
ESP32-S3 RTC GPIO range (0-21), so the rtc_gpio_hold_en() calls in
ESP32Board::enterDeepSleep() and StationG3Board::powerOff() return
ESP_ERR_INVALID_ARG on slot 2 and the NSS and LNA pins are not latched through
deep sleep. Fixing it means gpio_hold_en() plus gpio_deep_sleep_hold_en() in
shared code.
Brings in the external FEM gain preferences (fem_txgain, PR #3137 plus the
companion-side port), the AGC reset rxgain fix, the LR2021 preamble/IRQ
timeout logic, and assorted variant fixes (T096, T-Echo Card TCXO, promicro
pinmap, minewsemi, R1 Neo).
Conflict resolutions:
- SH1106Display: both sides fixed T-Beam Supreme startup independently. Kept
our _initialized guard and DISPLAY_ADDRESS_ALT override, took upstream's
SA0-pair fallback and its unconditional display.begin() so the frame buffer
is allocated even when no panel answers.
- MyMesh/SensorMesh/CommonCLI: took upstream's fem_txgain default and wiring,
kept our comments and the observer-side prefs layout.
Also fixes CustomLLCC68Wrapper, which upstream missed when sx126xResetAGC
gained its rx_boost_gain parameter. No variant builds that wrapper today, so
neither tree failed to compile.
PA PL1 re-targets the PA's DC-DC supply rail rather than selecting a
logic-level gain, and the serial CLI is serviced on every main-loop pass
regardless of whether a transmit is in flight. A `set radio.fem.txgain`
write could therefore move the rail mid-transmit, while the SX1262 was
still driving the PA at full input power.
Record the requested level in setPAGainEnable() and drive the pin from
setTxModeEnable(), which runs from onBeforeTransmit() ahead of
startTransmit(). The level only matters while transmitting, so deferring
costs nothing.
Document that the pref is saved immediately but applied at the next
transmit, so `get radio.fem.txgain` can lead the hardware until then.
Nothing has ever read it. The slot count comes from two other places: the
persisted array size (MAX_MQTT_SLOTS / RUNTIME_MQTT_SLOTS in MQTTPresets.h) and
the runtime cap MQTTBridge::getMaxActiveSlots(), which answers 5 with PSRAM and
2 without. A flag reading MAX_MQTT_BROKERS=3 sitting in every observer env
implies a third, lower limit that does not exist — it cost me a wrong answer
about how many MQTT slots a Heltec V4 exposes.
36 lines across 15 variants, all of them =3. Removing an unread -D cannot change
code: heltec_v4_repeater_observer_mqtt builds to a byte-identical size before and
after (1647744). The image checksum does differ, but so does it between two
clean builds of untouched source — ESP-IDF stamps the app descriptor with the
build time — so size is the meaningful comparison here.
All 606 envs still parse; heltec_v4, heltec_v3, station_g2, rak3112 and
xiao_s3_wio observer targets all build.
Adds Station_G3_ESP32_repeater_observer_mqtt and
Station_G3_ESP32_room_server_observer_mqtt, mirroring the known-good
Station G2 observer envs. The two boards are the same family — ESP32-S3,
qio_opi, PSRAM, 16 MB flash, SH1106 display — so the overlay ports across
unchanged: default_16MB.csv partitions, adafruit-full cert bundle,
MQTT bridge + SNMP, and the same lib_deps pinning.
Verified the G3 partition signature is byte-identical to the G2 observer's,
so the OTA partition-compatibility gate treats them the same. Both envs
build clean (1.67 MB of the 6.25 MB app slot, 28% RAM) and produce the full
CI artifact set via build.sh: .bin, -merged.bin and .partsig. Observer env
discovery now finds 32 envs (was 30) and the ArduinoJson pin check covers
both new sections.
Docs: added the G3 build commands and the two partition-table rows to
MQTT_IMPLEMENTATION.md.