Commit Graph
1047 Commits
Author SHA1 Message Date
agessaman 2e1a1410ce feat(mqtt): cooperative MQTT shutdown + OTA teardown barrier (Phase 5)
Wire the Phase 4 MQTTLifecycle state machine into MQTTBridge to replace the
blind vTaskDelete teardown that could kill the MQTT task mid-mbedTLS and then
free client buffers on a corrupted heap (the observed OTA teardown panic).

- MQTTBridge owns a MQTTLifecycle::Coordinator driven only by the loop task
  (Core 1) from begin()/end(); a nested LifecycleOps binds the host-tested Ops
  spec to FreeRTOS/PsychicMqttClient.
- end() requests a cooperative stop; the MQTT task (Core 0) tears down its own
  clients where the mbedTLS contexts live, acks via _stop_acked, and
  self-terminates. end() waits (bounded) for the ack, then frees queue/buffers.
- Bounded stop timeout -> reviewed fallback (force kill + Core-1 teardown) sets
  a dirty latch that withholds OTA flashing.
- begin() gains an idempotent double-call guard and syncs the Coordinator to
  Running.
- OTA teardown barrier: simple_repeater's deferred flash aborts/resumes unless
  end() reported a clean stop (canFlashAfterStop()).

Scope: minimal cooperative-shutdown unit. The volatile NTP/reconfigure handshake
replacement and the plain-data snapshot / consumer repointing (MQTT_OWNERSHIP.md
sections 1-3) are deferred. MQTT_STOP_TIMEOUT_MS is a Phase-0 placeholder pending
on-hardware characterization.

Native suite green (incl. test_mqtt_lifecycle); both observer firmware smoke
builds compile. Not yet hardware-validated (Phase 7 gate).
2026-07-19 00:25:37 -07:00
ViezeVingertjesandAdam Gessaman 3b69e7873b fix: guard HWCDC serial config behind ARDUINO_USB_MODE
setTxTimeoutMs() and setTxBufferSize() are HWCDC-only APIs; calling
them on HardwareSerial (UART-bridge boards like T-Beam) fails to compile.

Co-Authored-By: Adam Gessaman <adam@gessaman.com>
2026-07-18 22:43:55 +02:00
ViezeVingertjes fb2c61f862 fix: prevent ESP32 KISS modem stalls under USB backpressure
Switch ESP32-S3 KISS modem environments to HWCDC and move outbound KISS writes to a non-blocking queued frame path so loop() and TX completion keep progressing when the host reads slowly. Add native backpressure regression tests and correct the native_kiss_modem test filter so this suite runs directly with pio test.
2026-07-18 22:43:55 +02:00
agessaman cbbd01b620 feat(docs): add local testing instructions for MQTT functionality
Include detailed instructions for local testing of observer and WiFi
functionality without hardware. Document the use of a mock backend and
Wokwi ESP32-S3 simulation for easier development and testing.
Enhance the MQTT implementation documentation to improve developer
experience and facilitate testing workflows.
2026-07-18 13:19:27 -07:00
agessaman a7c1cc631f feat(webconfig): add web configuration portal and MQTT enhancements
Introduce a web configuration portal for easier node management and
provisioning without serial CLI. Enhance MQTT functionality with
improved IATA code validation, dynamic slot management, and
background NTP synchronization. Update web UI elements for better
user experience and security notes regarding open AP usage.
2026-07-18 09:34:11 -07:00
Scott Powell a0b52be4ad * RP2040 build fixes
* new prefs file now "/prefs.json"
2026-07-18 20:12:21 +10:00
Scott Powell 2189f2294c * added prefs initialisers to match original zeroed state 2026-07-18 19:22:53 +10:00
ripplebiz 795989b918 Merge pull request #2966 from Quency-D/heltec-rc32
Add Heltec rc32 board
2026-07-17 23:23:29 +10:00
Florent c644720ea7 uitask: screen and radio poweroff moved to board 2026-07-17 08:29:31 -04:00
fdlamotte 76c6e73fb6 Merge branch 'dev' into repeater_btn 2026-07-17 06:55:19 -04:00
Quency-D b26f53a263 Avoid waking display from rotary input 2026-07-17 15:35:07 +08:00
Scott Powell f515716032 * new NodePrefs for companion 2026-07-17 16:05:10 +10:00
agessaman dfee21a0c9 feat(webconfig): implement web configuration portal for ESP32 2026-07-16 17:00:22 -07:00
Scott Powell 85285c6cbc Merge branch 'dev' into config-serializer 2026-07-16 17:22:28 +10:00
Quency-D 05d4bd2f7f Add a rotary encoder 2026-07-15 17:45:24 +08:00
ripplebiz b55d69e57a Merge pull request #1983 from rgregg/rak-ethernet
Support for RAK ethernet module
2026-07-15 18:53:38 +10:00
Jaroslav Škarvada 15e259c572 Added MCU temp sensor to the companion
Fixes #2896
2026-07-14 17:43:33 +02:00
Scott Powell 2af1e6d099 * first draft of new ConfigSerializer. (simple embedded JSON prefs) 2026-07-15 01:23:57 +10:00
Quency-D 4d0ba1516c Remove the watchdog feeding operation from each iteration of the loop to reduce power consumption. 2026-07-14 17:23:13 +08:00
Ryan Gregg 16b76bd35a Merge remote-tracking branch 'upstream/dev' into rak-ethernet
# Conflicts:
#	examples/companion_radio/main.cpp
2026-07-13 23:06:00 -07:00
Alex Beal 07b543176b Merge branch 'dev' into pr-1446 2026-07-12 15:44:28 -06:00
agessaman 1d52161332 Merge branch 'restore/upstream-duty-cycle' into restore/fem-rxgain 2026-07-09 17:54:45 -07:00
agessaman 1c9c6292e5 fix(mqtt): shed retransmissions, not capture, when duty cycle starves the pool
Load-testing the restored token bucket at 'set dutycycle 1' showed MQTT
capture dropping to exactly the TX rate. Queued retransmissions hold static-
pool packets with no expiry, so throttling parks the whole pool in the send
queue; Dispatcher::checkRecv() then discards received packets before logRx()
ever feeds the bridge — each completed TX frees exactly one packet for
exactly one more RX.

Observer builds now use RxReservePacketManager (fork-owned header): once the
free pool drops below a quarter of the pool, outbound packets are refused and
freed, so RX allocation and MQTT capture continue at full rate while the node
sheds repeat load it has no TX budget for anyway. Non-observer builds keep
upstream pool behavior via the same factory; StaticPoolPacketManager stays
byte-identical to upstream.
2026-07-09 17:54:38 -07:00
agessaman b2e79d4735 fix(radio): drop companion FEM wiring; wire t096 + tracker_v2 FEM overrides
companion_radio has its own NodePrefs without radio_fem_rxgain (matching
upstream, which doesn't wire companion either), so the startup call added in
e905451d broke every companion build:
  MyMesh.cpp:973: error: 'struct NodePrefs' has no member named 'radio_fem_rxgain'
It went unnoticed behind the pre-existing companion build failures.

Also port upstream's FEM LNA overrides for heltec_t096 and heltec_tracker_v2
verbatim (board overrides + isLNAEnabled/const getters), so all three boards
upstream wires now match instead of reporting unsupported. Both variant files
compile; those targets still fail overall on the pre-existing non-observer
MQTT-source build-config issue (unchanged with this work stashed).
2026-07-09 12:25:23 -07:00
agessaman e905451dce feat(radio): drive LoRa FEM RX gain from radio_fem_rxgain (heltec_v4)
Completes the FEM RX-gain restoration begun in the CAD/prefs change, which
persisted radio_fem_rxgain but didn't yet drive the hardware. Also dropped
by the 22eb9b87 revert; restored to match upstream.

- MainBoard: setLoRaFemLnaEnabled()/canControlLoRaFemLna()/isLoRaFemLnaEnabled()
  virtuals (default: can't control — non-FEM boards report unsupported)
- heltec_v4: board overrides driving loRaFEMControl; LoRaFEMControl gains the
  isLNAEnabled() getter (it already tracked lna_enabled and drove the FEM)
- CLI: `set radio.fem.rxgain on/off` / `get radio.fem.rxgain` (guarded by
  canControlLoRaFemLna, so it reports "unsupported" on non-FEM boards)
- app startup applies the persisted pref: board.setLoRaFemLnaEnabled(
  _prefs.radio_fem_rxgain), beside setRxBoostedGainMode

Default is ON (upstream), so on FEM boards the LNA is enabled after upgrade —
a real reception behavior change to confirm on hardware. The other FEM
variants (heltec_t096/tower_v2/tracker_v2) need the same small board-override
addition; until then `radio.fem.rxgain` reports unsupported there (no
regression — status quo).

Builds: heltec_v4 repeater-observer + room-observer (FEM board), Heltec_v3
repeater (non-FEM, base virtuals no-op). NEEDS on-device validation on a
Heltec V4.
2026-07-09 11:20:07 -07:00
agessaman df90673d18 feat(radio): restore CAD support + radio_fem_rxgain persistence (upstream parity)
Continues restoring features dropped by the 22eb9b87 revert. Both were
upstream-tested code, not intentional fork removals.

CAD (hardware Channel Activity Detection / listen-before-talk before TX),
fully restored and functional:
- NodePrefs.cad_enabled + `set cad on/off` / `get cad` CLI (default off)
- RadioLibWrapper: _cad_enabled + setCADEnabled() + the scanChannel()/CAD
  branch in isChannelActive() (Phase 1 already restored the Dispatcher hook)
- getCADEnabled() overrides in the repeater/room/sensor apps (return the
  pref) and companion (always on, matching upstream)

radio_fem_rxgain: the NodePrefs field + /com_prefs persistence are restored
here at upstream's exact offsets (293 fem, 294 cad), which makes /com_prefs
byte-identical to upstream through the tail. The field is persisted and
defaults on (upstream default), but the per-board LNA *driving* + the
`radio.fem.rxgain` CLI are deferred to the FEM-hardware change (they depend
on board methods and want per-board bench testing).

The new-format /com_prefs tail grows from 3 to 5 bytes; the old-format
detection threshold and the host migration harness are updated accordingly
(all scenarios pass, incl. the non-MQTT-build variant).

Builds: Heltec_v3 repeater, repeater-observer, room-observer. (sensor /
plain-room / companion fail only on the pre-existing Timezone.h include
issue, unrelated to these changes.)
2026-07-09 11:12:57 -07:00
Florent 3ee2f77877 restore display and radio poweroff in ui 2026-07-06 08:46:57 -04:00
Florent 2efb3af69b repeater: poweroff on long press 2026-07-06 08:40:56 -04:00
Kevin Le 7d7de88707 board->powerOff() is sufficient to power off radio, display, GPS and components 2026-07-05 21:22:13 +07:00
Quency-D 2867542cfa Merge branch 'dev' into solar-watchdog 2026-07-04 16:47:37 +08:00
Neil Alexander 0d7379520f Fix recv_pkt_region incorrect usage
The `recv_pkt_region` is set when processing a flood packet in `filterRecvFloodPacket`
but direct/non-flood packets would never pass through that function, so the pointer was
not cleared for them.

`sendFloodReply` would then later use it blindly, which meant that the response would
either inherit the region from the last flood packet, or refer to a non-initialised pointer
if no region floods had been received yet.
2026-07-02 09:28:41 +01:00
Liam Cottle dc200cf22d Merge pull request #2639 from sefinek/fix/typos-in-comments
fix: fix typos in source code comments
2026-06-27 11:26:54 +12:00
agessaman 2eb41baeda refactor(mqtt): migrate observer settings to MQTTPrefs structure
Refactored the handling of observer-related settings by moving them from
NodePrefs to a new MQTTPrefs structure. This change centralizes MQTT,
WiFi, timezone, SNMP, and alert configurations, improving code organization
and maintainability. The new structure allows for better separation of
concerns and prepares the codebase for future enhancements.
2026-06-26 08:59:48 -07:00
taco 1f9bb67400 return bool when setting rx boost 2026-06-26 07:44:01 +10:00
taco 5d0ff7fe6e remove guard on MyMesh::setRxBoostedGain() 2026-06-26 07:06:37 +10:00
agessaman 7416d632b9 feat(mqtt): add NTP server configuration and diagnostics commands
Implemented new commands for configuring and diagnosing NTP server
settings in the MQTT bridge. Users can now set a custom NTP server
and probe connectivity to configured servers. This enhancement
improves time synchronization reliability for JWT authentication
and provides better diagnostics for NTP connectivity issues.
2026-06-24 17:14:11 -07:00
agessaman 125ddac184 feat(ota): add partition-table signature handling for OTA updates
Implemented functionality to generate and compare partition-table
signatures during OTA updates. This enhancement ensures that the
target build's partition layout matches the device's actual layout,
improving the reliability of OTA updates and preventing issues
related to partition changes.
2026-06-23 15:38:10 -07:00
agessaman 730eb37dbd feat(ota): implement build number suffix for firmware versioning
Enhanced the firmware versioning system by appending a build number
suffix when available, allowing for better tracking of published builds.
This change improves the OTA update process by providing clearer
versioning information in the embedded firmware string.
2026-06-23 12:55:07 -07:00
agessaman c1885fcc15 feat(ota): implement deferred OTA update scheduling and handling
Added support for deferred OTA updates in the MyMesh class, allowing
the system to schedule firmware updates to occur after a confirmation
reply is sent. This change improves the user experience by ensuring
that the update process does not block the main application loop,
allowing for smoother operation during firmware updates.
2026-06-22 22:33:57 -07:00
Ryan Gregg a206f3e066 Merge remote-tracking branch 'upstream/dev' into rak-ethernet
# Conflicts:
#	docs/faq.md
#	examples/companion_radio/main.cpp
2026-06-20 14:39:03 -07:00
agessaman 985fda1382 Add AlertReporter integration to MyMesh 2026-06-17 20:02:39 -07:00
Wessel Nieboer 7c8e092457 Have CAD be a separate toggle (set cad on/off) 2026-06-14 15:20:58 +02:00
Wessel Nieboer 4f9a091671 Use hardware channel activity detection for checking interference 2026-06-14 15:19:18 +02:00
Scott Powell 2e73fe948e * fix for anon lastmod 2026-06-14 18:54:51 +10:00
Scott Powell 07648e3344 * fix for anon contacts when full 2026-06-14 17:50:41 +10:00
Quency-D 5300fa18c7 Restore companion NodePrefs file ending 2026-06-13 17:40:11 +08:00
Quency-D 3ee58fd2e3 Remove companion FEM RX gain command IDs 2026-06-13 17:31:54 +08:00
Quency-D 9100a58671 Merge branch 'dev' into cli-lna-command 2026-06-10 11:30:04 +08:00
liamcottle ae0bb7ee95 use releasePacket instead of _mgr->free 2026-06-09 00:42:58 +12:00
liamcottle 07bfe90695 free packet on parse failure 2026-06-09 00:31:48 +12:00