SPI pins that are set to -1 cause OOB reads on NRF52. The unused Serial2 pin definitions were removed to avoid potential issues with the Uart framework.
Setting SPI pins to values that are OOB of the g_ADigitalPinMap[] array causes OOB reads. This variant.h has pin 0 as 0xFF which passes through as NRFX_SPIM_PIN_NOT_USED.
Picks up upstream MeshCore 1.17.0 and the dev commits that followed it.
Notable upstream content:
- 1.17.0 version/build-date bump in the example MyMesh headers.
- anon_req hardening: reply_path_len is now uint8_t with an isValidPathLen()
bounds check and a 0xFF sentinel; reply_path_hash_size is gone.
- LR2021 support (Meshnology W12, Seeed MeshTracker X1) incl. side detectors,
multi-SF and the new `extra.sf` get/set CLI.
- CustomLFS 0.2.2 -> 0.2.3 (GD25Q64C support).
- kiss_modem envs for several nRF52 variants; ThinkNode M6 GPS/flash fixes.
Conflicts resolved:
- platformio.ini: took upstream's CustomLFS 0.2.3, kept our lib_ignore for
the vendored PsychicMqttClient.
- CommonCLI.h: kept both upstream's USE_LR2021 configSideDetectors() hook and
our fault-alert callbacks.
NodePrefs gains upstream's extra_sf[4], which is not registered with
ConfigSerializer, so /prefs.json layout is unchanged.
Verified: 275/275 native host tests pass; Heltec_v3_repeater_observer_mqtt,
Heltec_v3_repeater and heltec_v4_repeater_observer_mqtt all build.
PA PL1 re-targets the PA's DC-DC supply rail rather than selecting a
logic-level gain, and the serial CLI is serviced on every main-loop pass
regardless of whether a transmit is in flight. A `set radio.fem.txgain`
write could therefore move the rail mid-transmit, while the SX1262 was
still driving the PA at full input power.
Record the requested level in setPAGainEnable() and drive the pin from
setTxModeEnable(), which runs from onBeforeTransmit() ahead of
startTransmit(). The level only matters while transmitting, so deferring
costs nothing.
Document that the pref is saved immediately but applied at the next
transmit, so `get radio.fem.txgain` can lead the hardware until then.
Nothing has ever read it. The slot count comes from two other places: the
persisted array size (MAX_MQTT_SLOTS / RUNTIME_MQTT_SLOTS in MQTTPresets.h) and
the runtime cap MQTTBridge::getMaxActiveSlots(), which answers 5 with PSRAM and
2 without. A flag reading MAX_MQTT_BROKERS=3 sitting in every observer env
implies a third, lower limit that does not exist — it cost me a wrong answer
about how many MQTT slots a Heltec V4 exposes.
36 lines across 15 variants, all of them =3. Removing an unread -D cannot change
code: heltec_v4_repeater_observer_mqtt builds to a byte-identical size before and
after (1647744). The image checksum does differ, but so does it between two
clean builds of untouched source — ESP-IDF stamps the app descriptor with the
build time — so size is the meaningful comparison here.
All 606 envs still parse; heltec_v4, heltec_v3, station_g2, rak3112 and
xiao_s3_wio observer targets all build.
mikecarper
taco
ripplebiz
Kevin Le
Rastislav Vysoky
agessaman
Huw Duddy
entr0p1
Hacuchino-hash