Resolve conflicts: keep MQTT/WiFi/timezone/analyzer defaults and get
handlers, add upstream neighbour sort guard, adc_multiplier and
pending_discover, and bootloader.ver get handler.
Co-authored-by: Cursor <cursoragent@cursor.com>
This change addresses two issues. The first is that the
LilyGo_TLora_V2_1_1_6_terminal_chat build would try to compile
simple_repeater/MyMesh.cpp. All other examples of terminal chat
targets are instead building simple_secure_chat/main.cpp . This
change would align this build to the rest of the builds.
The second issue, found during the course of investigating the
first, stems from simple_repeater/MyMesh.cpp using the
MAX_NEIGHBOURS #define to control whether the neighbor list is kept.
Repeaters that keep this list must define this value, and if the
value is not defined, then all neighbor-related functionality is
compiled out. However, the code that replies to
REQ_TYPE_GET_NEIGHBOURS did not properly check for this #define,
and thus any target that compiles simple_repeater/MyMesh.cpp
without defining MAX_NEIGHBOURS would get an undefined variable
compilation error.
As a practical matter though, there are no targets that compile
simple_repeater/MyMesh.cpp AND do not define MAX_NEIGHBOURS,
except this build due to the first issue. As a result, the
second issue is addressed only as a matter of completeness. The
expected behavior with this change is that such a repeater would
send a valid reply indicating zero known neighbors.
Resolve conflict in heltec_tracker_v2/platformio.ini: keep
SX126X_REGISTER_PATCH=1 from upstream and retain GC1109 comment.
Co-authored-by: Cursor <cursoragent@cursor.com>
Sensors connected via the Grove I2C connector (D18/D17) were not detected
because the firmware scanned the OLED I2C bus (Wire, D14/D15) by default.
Adding ENV_PIN_SDA/SCL flags directs EnvironmentSensorManager to use Wire1,
matching the physical Grove connector pinout.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Resolve conflict in variants/heltec_v4/platformio.ini by taking
origin/dev version for PA pin comments and SX126X_RX_BOOSTED_GAIN.
Co-authored-by: Cursor <cursoragent@cursor.com>
- Implemented PSRAM availability checks and logging to assist in debugging memory fragmentation on boards with external RAM.
- Enhanced logging to provide detailed information about PSRAM size, free memory, and initialization status.
- Updated platformio.ini files across multiple variants to remove obsolete mbedTLS configuration flags, streamlining the build process.
- Added new build flags for mbedTLS: CONFIG_MBEDTLS_ASYMMETRIC_CONTENT_LEN, CONFIG_MBEDTLS_SSL_IN_CONTENT_LEN, and CONFIG_MBEDTLS_SSL_OUT_CONTENT_LEN.
- These changes improve the handling of SSL content lengths, optimizing performance for various hardware variants.
- Updated source filters to include MQTTBridge and MQTTMessageBuilder in relevant configurations.
- Added memory debugging features to log heap usage and fragmentation recovery for MQTT clients.
- Introduced `recreateMqttClientsForFragmentationRecovery()` to manage MQTT client lifecycles and reduce memory fragmentation.
- Updated critical memory checks to log detailed heap statistics and active MQTT client counts.
- Included new debug logging for memory status every 60 seconds when memory debugging is enabled.
This update aims to improve stability and performance in memory-constrained environments.
- Trigger noise floor calibration every 2s and AGC reset every 30s in main loop.
- Reorder loop to match Dispatcher: calibrate + radio.loop() before AGC reset
and recvRaw() so RSSI is never sampled right after startReceive().
- Update protocol doc with calibration intervals and typical noise floor range.
- Variant platformio.ini updates (heltec_v3, rak4631).