Organize test results and historical release docs
This commit is contained in:
1 parent
d44910865c
commit
e96918cd91
130 files changed
+8975
-7736
No files matched your search
@@ -1044,7 +1044,7 @@ set usb.logging on
|
||||
|
||||
Verify with `get powersaving` (expect `off`) and `get usb.logging` (expect `on`).
|
||||
Both settings are saved; disabling logging later does not restore power
|
||||
saving. This works around the [released USB sleep bug](releases/1.17.1.5.md#g3-usb-disappearance-with-power-saving-enabled).
|
||||
saving. This works around the [released USB sleep bug](old-releases/1.17.1.5.md#g3-usb-disappearance-with-power-saving-enabled).
|
||||
nRF52 does not need this ESP32 workaround.
|
||||
|
||||
These commands are compiled into ordinary USB-loggable artifacts and every
|
||||
@@ -1443,7 +1443,7 @@ Station G2/G3 targets default to `off`.
|
||||
|
||||
**Notes:**
|
||||
- `get rxps.wd` reports the radio watchdogs' soft and hard recovery counts.
|
||||
See [receive calibration and recovery](radio_receive_calibration.md) for
|
||||
See [receive calibration and recovery](test-results/radio_receive_calibration.md) for
|
||||
noise sampling, CAD handling, and the continuous-RX mode check.
|
||||
- `get radio.rxps.config` adds the persisted level and preamble assumption to
|
||||
the on/off and timing values. Deployment tools use it to restore a
|
||||
@@ -2154,7 +2154,7 @@ minutes when the terminal is closed, even with a computer attached. The
|
||||
source fix blocks ESP32 light sleep while a native USB host is attached or
|
||||
live USB logging is enabled; ordinary CPU idle/yield remains available.
|
||||
The G3 button also wakes the device for at least two minutes. See the
|
||||
[G3 release note](releases/1.17.1.5.md#g3-usb-disappearance-with-power-saving-enabled)
|
||||
[G3 release note](old-releases/1.17.1.5.md#g3-usb-disappearance-with-power-saving-enabled)
|
||||
for verification steps and the distinction between the fix and the published
|
||||
binaries.
|
||||
|
||||
@@ -2257,7 +2257,7 @@ The pin number is the Arduino pin number used by that target (the normal GPIO nu
|
||||
**1.17.1.5 infrastructure bug:** affected Repeater, Room Server, and Sensor
|
||||
images accept `get path.hash.mode` but report `unknown config` for the setter.
|
||||
The command was not renamed. The source correction restores the setter;
|
||||
installed images need an updated build. See the [setting-dispatch audit](cli_settings_audit.md).
|
||||
installed images need an updated build. See the [setting-dispatch audit](test-results/cli_settings_audit.md).
|
||||
|
||||
**Usage:**
|
||||
- `get path.hash.mode`
|
||||
@@ -4770,7 +4770,7 @@ displaying a version neither grants OTA capability nor bypasses install checks.
|
||||
The fix is in MeshCore application firmware; installing another bootloader alone
|
||||
does not update an older application's version reader.
|
||||
|
||||
See the [stock bootloader audit](bootloader_version_stock_audit.md) for tested
|
||||
See the [stock bootloader audit](test-results/bootloader_version_stock_audit.md) for tested
|
||||
manufacturer images and the boards still requiring untouched factory dumps.
|
||||
|
||||
---
|
||||
|
||||
Reference in new issue
Block a user