diff --git a/boards/meshnology_w12.json b/boards/meshnology_w12.json new file mode 100644 index 000000000..2e74af9b3 --- /dev/null +++ b/boards/meshnology_w12.json @@ -0,0 +1,43 @@ +{ + "build": { + "arduino": { + "ldscript": "esp32s3_out.ld", + "partitions": "default_16MB.csv", + "memory_type": "qio_opi" + }, + "core": "esp32", + "extra_flags": [ + "-DBOARD_HAS_PSRAM", + "-DARDUINO_USB_CDC_ON_BOOT=1", + "-DARDUINO_USB_MODE=1", + "-DARDUINO_RUNNING_CORE=1", + "-DARDUINO_EVENT_RUNNING_CORE=1" + ], + "f_cpu": "240000000L", + "f_flash": "80000000L", + "flash_mode": "qio", + "psram_type": "opi", + "hwids": [["0x303A", "0x0002"], ["0x303A", "0x1001"]], + "mcu": "esp32s3", + "variant": "meshnology_w12" + }, + "connectivity": ["wifi", "bluetooth", "lora"], + "debug": { + "default_tool": "esp-builtin", + "onboard_tools": ["esp-builtin"], + "openocd_target": "esp32s3.cfg" + }, + "frameworks": ["arduino", "espidf"], + "name": "heltec_wifi_lora_32 v5 (16 MB FLASH, 8 MB PSRAM)", + "upload": { + "flash_size": "16MB", + "maximum_ram_size": 327680, + "maximum_size": 16777216, + "use_1200bps_touch": true, + "wait_for_upload_port": true, + "require_upload_port": true, + "speed": 921600 + }, + "url": "https://heltec.org/", + "vendor": "heltec" +} \ No newline at end of file diff --git a/boards/seeed-mesh-tracker-x1.json b/boards/seeed-mesh-tracker-x1.json new file mode 100644 index 000000000..347aca53f --- /dev/null +++ b/boards/seeed-mesh-tracker-x1.json @@ -0,0 +1,60 @@ +{ + "build": { + "arduino": { + "ldscript": "nrf52840_s140_v7.ld" + }, + "core": "nRF5", + "cpu": "cortex-m4", + "extra_flags": "-DARDUINO_WIO_WM1110 -DNRF52840_XXAA", + "f_cpu": "64000000L", + "hwids": [ + ["0x239A", "0x8029"], + ["0x239A", "0x0029"], + ["0x239A", "0x002A"], + ["0x239A", "0x802A"], + ["0x2886", "0x0057"] + ], + "usb_product": "X1-BOOT", + "mcu": "nrf52840", + "variant": "Seeed_Mesh-Tracker-X1", + "bsp": { + "name": "adafruit" + }, + "softdevice": { + "sd_flags": "-DS140", + "sd_name": "s140", + "sd_version": "7.3.0", + "sd_fwid": "0x0123" + }, + "bootloader": { + "settings_addr": "0xFF000" + } + }, + "connectivity": ["bluetooth"], + "debug": { + "jlink_device": "nRF52840_xxAA", + "svd_path": "nrf52840.svd", + "openocd_target": "nrf52.cfg" + }, + "frameworks": ["arduino"], + "name": "Seeed SenseCAP MeshTracker X1", + "upload": { + "maximum_ram_size": 248832, + "maximum_size": 815104, + "speed": 115200, + "protocol": "nrfutil", + "protocols": [ + "jlink", + "nrfjprog", + "nrfutil", + "stlink", + "cmsis-dap", + "blackmagic" + ], + "use_1200bps_touch": true, + "require_upload_port": true, + "wait_for_upload_port": true + }, + "url": "https://www.seeedstudio.com/SenseCAP-MeshTracker-X1-for-Meshtastic-p-6793.html", + "vendor": "Seeed Studio" +} diff --git a/build.sh b/build.sh index 13939a5d9..5d6ae4439 100755 --- a/build.sh +++ b/build.sh @@ -37,6 +37,9 @@ $ sh build.sh build-repeater-firmwares Build all chat room server firmwares $ sh build.sh build-room-server-firmwares +Build all kiss radio firmwares +$ sh build.sh build-kiss-radio-firmwares + Environment Variables: DISABLE_DEBUG=1: Disables all debug logging flags (MESH_DEBUG, MESH_PACKET_LOGGING, etc.) If not set, debug flags from variant platformio.ini files are used. @@ -297,6 +300,17 @@ build_room_server_firmwares() { } +build_kiss_modem_firmwares() { + +# # build specific kiss radio firmwares +# build_firmware "Heltec_v3_kiss_modem" +# build_firmware "RAK_4631_kiss_modem" + + # build all room server firmwares + build_all_firmwares_by_suffix "_kiss_modem" + +} + build_firmwares() { build_companion_firmwares build_repeater_firmwares @@ -333,6 +347,8 @@ elif [[ $1 == "build-repeater-firmwares" ]]; then build_repeater_firmwares elif [[ $1 == "build-room-server-firmwares" ]]; then build_room_server_firmwares +elif [[ $1 == "build-kiss-radio-firmwares" ]]; then + build_kiss_modem_firmwares elif [[ $1 == "get-companion-firmwares-to-build" ]]; then get_pio_envs_ending_with_string "_companion_radio_usb" get_pio_envs_ending_with_string "_companion_radio_ble" diff --git a/docs/companion_protocol.md b/docs/companion_protocol.md index 7cca7bc9a..8c6b84b97 100644 --- a/docs/companion_protocol.md +++ b/docs/companion_protocol.md @@ -440,6 +440,8 @@ Byte 0: 0x14 - Uses a secret key derived from the channel name - It is the first 16 bytes of `sha256("#test")` - For example hashtag channel `#test` has the key: `9cd8fcf22a47333b591d96a2b848b73f` + - Traffic is encrypted on air, but anyone who knows or guesses the channel + name can derive the key. Hashtag channels should not be treated as private. - Used as a topic based public group chat, separate from the default public channel 3. **Private Channels** - Uses a randomly generated 16-byte secret key diff --git a/docs/payloads.md b/docs/payloads.md index b4a98b385..a2945e27f 100644 --- a/docs/payloads.md +++ b/docs/payloads.md @@ -236,6 +236,9 @@ txt_type The plaintext contained in the ciphertext matches the format described in [plain text message](#plain-text-message). Specifically, it consists of a four byte timestamp, a flags byte, and the message. The flags byte will generally be `0x00` because it is a "plain text message". The message will be of the form `: ` (eg., `user123: I'm on my way`). +The sender name is unverified message text. Group messages contain no sender +signature, so any channel-key holder can choose any sender name. + ## Group datagram | Field | Size (bytes) | Description | diff --git a/examples/companion_radio/MyMesh.cpp b/examples/companion_radio/MyMesh.cpp index 46f70d789..9e389e99e 100644 --- a/examples/companion_radio/MyMesh.cpp +++ b/examples/companion_radio/MyMesh.cpp @@ -259,7 +259,7 @@ float MyMesh::getAirtimeBudgetFactor() const { } bool MyMesh::getCADEnabled() const { - return true; // hardware CAD before TX (no CLI toggle on companion; enabled by default) + return false; // hardware CAD before TX (disabled by default, until configurable) } int MyMesh::getInterferenceThreshold() const { diff --git a/examples/companion_radio/MyMesh.h b/examples/companion_radio/MyMesh.h index d95b073fb..f73fe0e06 100644 --- a/examples/companion_radio/MyMesh.h +++ b/examples/companion_radio/MyMesh.h @@ -8,11 +8,11 @@ #define FIRMWARE_VER_CODE 13 #ifndef FIRMWARE_BUILD_DATE -#define FIRMWARE_BUILD_DATE "6 Jun 2026" +#define FIRMWARE_BUILD_DATE "9 Aug 2026" #endif #ifndef FIRMWARE_VERSION -#define FIRMWARE_VERSION "v1.16.0" +#define FIRMWARE_VERSION "v1.17.0" #endif #if defined(NRF52_PLATFORM) || defined(STM32_PLATFORM) diff --git a/examples/companion_radio/NodePrefs.h b/examples/companion_radio/NodePrefs.h index 39a5386a9..4ec1803e1 100644 --- a/examples/companion_radio/NodePrefs.h +++ b/examples/companion_radio/NodePrefs.h @@ -28,6 +28,7 @@ public: uint32_t ble_pin = 0; uint8_t advert_loc_policy = 0; uint8_t buzzer_quiet = 0; + uint8_t vibe_quiet = 0; uint8_t gps_enabled = 0; // GPS enabled flag (0=disabled, 1=enabled) uint32_t gps_interval = 0; // GPS read interval in seconds uint8_t autoadd_config = 0; // bitmask for auto-add contacts config @@ -101,6 +102,7 @@ private: def("defs_key", (void *) _parent->default_scope_key, sizeof(_parent->default_scope_key)); def("pin", _parent->ble_pin); def("buzz_q", _parent->buzzer_quiet); + def("vibe_q", _parent->vibe_quiet); def("auto_add", _parent->autoadd_config); // bitmask for auto-add contacts config def("man_add", _parent->manual_add_contacts); def("tel_base", _parent->telemetry_mode_base); diff --git a/examples/companion_radio/ui-orig/UITask.cpp b/examples/companion_radio/ui-orig/UITask.cpp index 09fc8e770..b49b05dd1 100644 --- a/examples/companion_radio/ui-orig/UITask.cpp +++ b/examples/companion_radio/ui-orig/UITask.cpp @@ -6,12 +6,19 @@ #define AUTO_OFF_MILLIS 15000 // 15 seconds #define BOOT_SCREEN_MILLIS 3000 // 3 seconds -#ifdef PIN_STATUS_LED +#if defined(PIN_STATUS_LED) || defined(PIN_STATUS_LED_R) #define LED_ON_MILLIS 20 #define LED_ON_MSG_MILLIS 200 #define LED_CYCLE_MILLIS 4000 #endif +#if defined(PIN_STATUS_LED_R) && defined(PIN_STATUS_LED_G) && defined(PIN_STATUS_LED_B) +#define STATUS_LED_RGB 1 +#ifndef LOW_BATT_MILLIVOLTS +#define LOW_BATT_MILLIVOLTS 3500 +#endif +#endif + #ifndef USER_BTN_PRESSED #define USER_BTN_PRESSED LOW #endif @@ -60,6 +67,11 @@ void UITask::begin(DisplayDriver* display, SensorManager* sensors, NodePrefs* no buzzer.startup(); #endif +#ifdef HAS_DRV2605 + vibration.begin(); + vibration.quiet(_node_prefs->vibe_quiet); +#endif + // Initialize digital button if available #ifdef PIN_USER_BTN _userButton = new Button(PIN_USER_BTN, USER_BTN_PRESSED); @@ -130,6 +142,10 @@ void UITask::clearMsgPreview() { void UITask::newMsg(uint8_t path_len, const char* from_name, const char* text, int msgcount) { _msgcount = msgcount; +#ifdef HAS_DRV2605 + vibration.trigger(); // vibrate even while the app is connected (honors quiet + cooldown) +#endif + if (path_len == 0xFF) { sprintf(_origin, "(F) %s", from_name); } else { @@ -260,8 +276,114 @@ void UITask::renderCurrScreen() { _need_refresh = false; } +#ifdef STATUS_LED_RGB +static void statusLedWrite(uint8_t r, uint8_t g, uint8_t b) { + analogWrite(PIN_STATUS_LED_R, r); + analogWrite(PIN_STATUS_LED_G, g); + analogWrite(PIN_STATUS_LED_B, b); +} + +static void statusLedWheel(uint8_t pos) { // smooth hue sweep, 0..255 + if (pos < 85) { + statusLedWrite(255 - pos * 3, pos * 3, 0); + } else if (pos < 170) { + pos -= 85; + statusLedWrite(0, 255 - pos * 3, pos * 3); + } else { + pos -= 170; + statusLedWrite(pos * 3, 0, 255 - pos * 3); + } +} +#endif + void UITask::userLedHandler() { -#ifdef PIN_STATUS_LED +#ifdef STATUS_LED_RGB + static bool booted = false; + static bool flourish_active = false; + static unsigned long flourish_until = 0; + static int prev_msgcount = 0; + static int state = 0; + static unsigned long next_change = 0; + static int last_increment = 0; + static unsigned long next_batt_check = 0; + static bool low_batt = false; + + unsigned long cur_time = millis(); + + if (!booted) { // color sweep on boot + booted = true; + flourish_until = cur_time + 1200; + flourish_active = true; + } + if (_msgcount > prev_msgcount) { // color sweep when a new message arrives + flourish_until = cur_time + 800; + flourish_active = true; + } + prev_msgcount = _msgcount; + + if (flourish_active) { + if (cur_time < flourish_until) { + statusLedWheel((cur_time % 1200) * 255 / 1200); + return; + } + statusLedWrite(0, 0, 0); + flourish_active = false; + state = 0; + next_change = cur_time; + } + + if (cur_time > next_batt_check) { // battery reads are not free, keep them rare + low_batt = _board->getBattMilliVolts() < LOW_BATT_MILLIVOLTS; + next_batt_check = cur_time + 60000; + } + +#ifdef EXT_CHRG_DETECT + // charge status display while docked (skipped when messages are waiting, + // so the unread indication is never masked) + static unsigned long next_pwr_check = 0; + static bool ext_powered = false, ext_charging = false; + if (cur_time > next_pwr_check) { + ext_powered = _board->isExternalPowered(); + ext_charging = ext_powered && digitalRead(EXT_CHRG_DETECT) == LOW; + next_pwr_check = cur_time + 1000; + } + if (ext_powered && _msgcount == 0) { + if (ext_charging) { + // amber breathing while charging + int ph = cur_time % 2000; + int v = ph < 1000 ? ph : 2000 - ph; + uint8_t lvl = (uint8_t)(v * 255 / 1000); + statusLedWrite(lvl, (uint8_t)(lvl * 35 / 100), 0); + } else { + statusLedWrite(0, 40, 0); // dim solid green: charge complete + } + state = 0; + next_change = cur_time; + return; + } +#endif + + if (cur_time > next_change) { + if (state == 0) { + state = 1; + last_increment = (_msgcount > 0) ? LED_ON_MSG_MILLIS : LED_ON_MILLIS; + next_change = cur_time + last_increment; + if (low_batt) { + statusLedWrite(255, 0, 0); // red: battery low + } else if (_msgcount > 0) { + statusLedWrite(255, 90, 0); // amber: unread messages + } else if (_connected) { + statusLedWrite(0, 0, 255); // blue: app connected + } else { + statusLedWrite(0, 255, 0); // green: heartbeat + } + } else { + state = 0; + next_change = cur_time + LED_CYCLE_MILLIS - last_increment; + statusLedWrite(0, 0, 0); + } + } +#elif defined(PIN_STATUS_LED) static int state = 0; static int next_change = 0; static int last_increment = 0; @@ -406,8 +528,26 @@ void UITask::handleButtonDoublePress() { void UITask::handleButtonTriplePress() { MESH_DEBUG_PRINTLN("UITask: triple press triggered"); - // Toggle buzzer quiet mode - #ifdef PIN_BUZZER +#if defined(PIN_BUZZER) && defined(HAS_DRV2605) + // cycle alert modes: Buzz+Vibe -> Buzz only -> Vibe only -> Silent + int mode = (_node_prefs->buzzer_quiet ? 2 : 0) | (_node_prefs->vibe_quiet ? 1 : 0); + mode = (mode + 1) & 3; + _node_prefs->buzzer_quiet = (mode & 2) ? 1 : 0; + _node_prefs->vibe_quiet = (mode & 1) ? 1 : 0; + buzzer.quiet(_node_prefs->buzzer_quiet); + vibration.quiet(_node_prefs->vibe_quiet); + // audible/tactile confirmation of the new mode (no screen on some boards) + if (!_node_prefs->buzzer_quiet) notify(UIEventType::ack); + if (!_node_prefs->vibe_quiet) vibration.trigger(true); + switch (mode) { + case 0: sprintf(_alert, "Alerts: Buzz+Vibe"); break; + case 1: sprintf(_alert, "Alerts: Buzz only"); break; + case 2: sprintf(_alert, "Alerts: Vibe only"); break; + default: sprintf(_alert, "Alerts: Silent"); break; + } + the_mesh.savePrefs(); + _need_refresh = true; +#elif defined(PIN_BUZZER) if (buzzer.isQuiet()) { buzzer.quiet(false); notify(UIEventType::ack); @@ -419,7 +559,7 @@ void UITask::handleButtonTriplePress() { _node_prefs->buzzer_quiet = buzzer.isQuiet(); the_mesh.savePrefs(); _need_refresh = true; - #endif +#endif } void UITask::handleButtonQuadruplePress() { diff --git a/examples/companion_radio/ui-orig/UITask.h b/examples/companion_radio/ui-orig/UITask.h index 961c07a03..02d126e8f 100644 --- a/examples/companion_radio/ui-orig/UITask.h +++ b/examples/companion_radio/ui-orig/UITask.h @@ -14,11 +14,18 @@ #include "Button.h" +#ifdef HAS_DRV2605 + #include +#endif + class UITask : public AbstractUITask { DisplayDriver* _display; SensorManager* _sensors; #ifdef PIN_BUZZER genericBuzzer buzzer; +#endif +#ifdef HAS_DRV2605 + DRV2605Vibration vibration; #endif unsigned long _next_refresh, _auto_off; NodePrefs* _node_prefs; diff --git a/examples/simple_repeater/MyMesh.cpp b/examples/simple_repeater/MyMesh.cpp index db4878c40..41b70da14 100644 --- a/examples/simple_repeater/MyMesh.cpp +++ b/examples/simple_repeater/MyMesh.cpp @@ -191,11 +191,10 @@ static int cmp_neighbours_weakest_to_strongest(const void* a, const void* b) { uint8_t MyMesh::handleAnonRegionsReq(const mesh::Identity& sender, uint32_t sender_timestamp, const uint8_t* data) { if (anon_limiter.allow(rtc_clock.getCurrentTime())) { // request data has: {reply-path-len}{reply-path} - reply_path_len = *data & 63; - reply_path_hash_size = (*data >> 6) + 1; - data++; + reply_path_len = *data++; + if (!mesh::Packet::isValidPathLen(reply_path_len)) return 0; // reject - bad encoding - memcpy(reply_path, data, ((uint8_t)reply_path_len) * reply_path_hash_size); + mesh::Packet::writePath(reply_path, data, reply_path_len); // data += (uint8_t)reply_path_len * reply_path_hash_size; memcpy(reply_data, &sender_timestamp, 4); // prefix with sender_timestamp, like a tag @@ -210,11 +209,10 @@ uint8_t MyMesh::handleAnonRegionsReq(const mesh::Identity& sender, uint32_t send uint8_t MyMesh::handleAnonOwnerReq(const mesh::Identity& sender, uint32_t sender_timestamp, const uint8_t* data) { if (anon_limiter.allow(rtc_clock.getCurrentTime())) { // request data has: {reply-path-len}{reply-path} - reply_path_len = *data & 63; - reply_path_hash_size = (*data >> 6) + 1; - data++; + reply_path_len = *data++; + if (!mesh::Packet::isValidPathLen(reply_path_len)) return 0; // reject - bad encoding - memcpy(reply_path, data, ((uint8_t)reply_path_len) * reply_path_hash_size); + mesh::Packet::writePath(reply_path, data, reply_path_len); // data += (uint8_t)reply_path_len * reply_path_hash_size; memcpy(reply_data, &sender_timestamp, 4); // prefix with sender_timestamp, like a tag @@ -230,11 +228,10 @@ uint8_t MyMesh::handleAnonOwnerReq(const mesh::Identity& sender, uint32_t sender uint8_t MyMesh::handleAnonClockReq(const mesh::Identity& sender, uint32_t sender_timestamp, const uint8_t* data) { if (anon_limiter.allow(rtc_clock.getCurrentTime())) { // request data has: {reply-path-len}{reply-path} - reply_path_len = *data & 63; - reply_path_hash_size = (*data >> 6) + 1; - data++; + reply_path_len = *data++; + if (!mesh::Packet::isValidPathLen(reply_path_len)) return 0; // reject - bad encoding - memcpy(reply_path, data, ((uint8_t)reply_path_len) * reply_path_hash_size); + mesh::Packet::writePath(reply_path, data, reply_path_len); // data += (uint8_t)reply_path_len * reply_path_hash_size; memcpy(reply_data, &sender_timestamp, 4); // prefix with sender_timestamp, like a tag @@ -665,7 +662,7 @@ void MyMesh::onAnonDataRecv(mesh::Packet *packet, const uint8_t *secret, const m data[len] = 0; // ensure null terminator uint8_t reply_len; - reply_path_len = -1; + reply_path_len = 0xFF; if (data[4] == 0 || data[4] >= ' ') { // is password, ie. a login request reply_len = handleLoginReq(sender, secret, timestamp, &data[4], packet->isRouteFlood()); } else if (data[4] == ANON_REQ_TYPE_REGIONS && packet->isRouteDirect()) { @@ -685,13 +682,12 @@ void MyMesh::onAnonDataRecv(mesh::Packet *packet, const uint8_t *secret, const m mesh::Packet* path = createPathReturn(sender, secret, packet->path, packet->path_len, PAYLOAD_TYPE_RESPONSE, reply_data, reply_len); if (path) sendFloodReply(path, SERVER_RESPONSE_DELAY, packet->getPathHashSize()); - } else if (reply_path_len < 0) { + } else if (reply_path_len == 0xFF) { mesh::Packet* reply = createDatagram(PAYLOAD_TYPE_RESPONSE, sender, secret, reply_data, reply_len); if (reply) sendFloodReply(reply, SERVER_RESPONSE_DELAY, packet->getPathHashSize()); } else { mesh::Packet* reply = createDatagram(PAYLOAD_TYPE_RESPONSE, sender, secret, reply_data, reply_len); - uint8_t path_len = ((reply_path_hash_size - 1) << 6) | (reply_path_len & 63); - if (reply) sendDirect(reply, reply_path, path_len, SERVER_RESPONSE_DELAY); + if (reply) sendDirect(reply, reply_path, reply_path_len, SERVER_RESPONSE_DELAY); } } } @@ -1319,6 +1315,12 @@ bool MyMesh::setRxBoostedGain(bool enable) { return radio_driver.setRxBoostedGainMode(enable); } +#if defined(USE_LR2021) +bool MyMesh::configSideDetectors(const uint8_t sideDetSFs[], uint8_t num, float bw) { + return radio_driver.configSideDetectors(sideDetSFs, num, bw); +} +#endif + void MyMesh::formatNeighborsReply(char *reply) { char *dp = reply; diff --git a/examples/simple_repeater/MyMesh.h b/examples/simple_repeater/MyMesh.h index ec84dbcea..4a7d5252b 100644 --- a/examples/simple_repeater/MyMesh.h +++ b/examples/simple_repeater/MyMesh.h @@ -79,11 +79,11 @@ struct NeighbourInfo { }; #ifndef FIRMWARE_BUILD_DATE - #define FIRMWARE_BUILD_DATE "6 Jun 2026" + #define FIRMWARE_BUILD_DATE "9 Aug 2026" #endif #ifndef FIRMWARE_VERSION - #define FIRMWARE_VERSION "v1.16.0" + #define FIRMWARE_VERSION "v1.17.0" #endif #define FIRMWARE_ROLE "repeater" @@ -105,8 +105,7 @@ class MyMesh : public mesh::Mesh, public CommonCLICallbacks CommonCLI _cli; uint8_t reply_data[MAX_PACKET_PAYLOAD]; uint8_t reply_path[MAX_PATH_SIZE]; - int8_t reply_path_len; - uint8_t reply_path_hash_size; + uint8_t reply_path_len; TransportKeyStore key_store; RegionMap region_map, temp_map; RegionEntry* load_stack[8]; @@ -499,4 +498,8 @@ public: bool setRxBoostedGain(bool enable) override; + #if defined(USE_LR2021) + virtual bool configSideDetectors(const uint8_t sideDetSFs[], uint8_t num, float bw) override; + #endif + }; diff --git a/examples/simple_room_server/MyMesh.h b/examples/simple_room_server/MyMesh.h index f5c6f0368..fb28605fa 100644 --- a/examples/simple_room_server/MyMesh.h +++ b/examples/simple_room_server/MyMesh.h @@ -38,11 +38,11 @@ /* ------------------------------ Config -------------------------------- */ #ifndef FIRMWARE_BUILD_DATE - #define FIRMWARE_BUILD_DATE "6 Jun 2026" + #define FIRMWARE_BUILD_DATE "9 Aug 2026" #endif #ifndef FIRMWARE_VERSION - #define FIRMWARE_VERSION "v1.16.0" + #define FIRMWARE_VERSION "v1.17.0" #endif #ifndef LORA_FREQ diff --git a/examples/simple_sensor/SensorMesh.h b/examples/simple_sensor/SensorMesh.h index 1d65b8772..3a33b638c 100644 --- a/examples/simple_sensor/SensorMesh.h +++ b/examples/simple_sensor/SensorMesh.h @@ -34,11 +34,11 @@ #define PERM_RECV_ALERTS_HI (1 << 7) // high priority alerts #ifndef FIRMWARE_BUILD_DATE - #define FIRMWARE_BUILD_DATE "6 Jun 2026" + #define FIRMWARE_BUILD_DATE "9 Aug 2026" #endif #ifndef FIRMWARE_VERSION - #define FIRMWARE_VERSION "v1.16.0" + #define FIRMWARE_VERSION "v1.17.0" #endif #define FIRMWARE_ROLE "sensor" diff --git a/platformio.ini b/platformio.ini index c320db6dc..6c012f1e5 100644 --- a/platformio.ini +++ b/platformio.ini @@ -103,7 +103,7 @@ build_flags = ${arduino_base.build_flags} -D USE_CC310_HW_CRYPTO=1 lib_deps = ${arduino_base.lib_deps} - https://github.com/oltaco/CustomLFS#0.2.2 + https://github.com/oltaco/CustomLFS#0.2.3 ; Vendored ESP-IDF MQTT client; the LDF otherwise pulls it into non-ESP builds. lib_ignore = PsychicMqttClient ; ----------------- RP2040 --------------------- diff --git a/src/helpers/CommonCLI.cpp b/src/helpers/CommonCLI.cpp index df1514d7b..e579ba24a 100644 --- a/src/helpers/CommonCLI.cpp +++ b/src/helpers/CommonCLI.cpp @@ -1451,6 +1451,28 @@ void CommonCLI::handleSetCmd(uint32_t sender_timestamp, char* command, char* rep _prefs->adc_multiplier = 0.0f; strcpy(reply, "Error: unsupported"); }; + #if defined(USE_LR2021) + } else if (memcmp(config, "extra.sf ", 9) == 0) { + strcpy(tmp, &config[9]); + const char *parts[4]; + uint8_t sideDetSFs[4]; + int num = mesh::Utils::parseTextParts(tmp, parts, 4); + if (num > 3) { + sprintf(reply, "Invalid extra SF config"); + } else { + for (int i = 0; i < num; i++) { + sideDetSFs[i] = atoi(parts[i]); + } + sideDetSFs[num] = 0; + if (_callbacks->configSideDetectors(sideDetSFs, num, _prefs->bw)) { + for (int i = 0; i <= num; i++) _prefs->extra_sf[i] = sideDetSFs[i]; + savePrefs(); + sprintf(reply, "OK - extra SFs set"); + } else { + sprintf(reply, "Invalid extra SF config"); + } + } + #endif } else { sprintf(reply, "unknown config: %s", config); } @@ -1626,6 +1648,14 @@ void CommonCLI::handleGetCmd(uint32_t sender_timestamp, char* command, char* rep #else strcpy(reply, "ERROR: Power management not supported"); #endif + } else if (memcmp(config, "extra.sf", 8) == 0) { + char* tmp = reply; + for (int i = 0; i < 3 && _prefs->extra_sf[i] != 0; i++) { + tmp += sprintf(tmp, "%s%d", (i == 0) ? "" : ",", _prefs->extra_sf[i]); + } + if (tmp == reply) { + sprintf(reply, "No extra SF configured"); + } } else { sprintf(reply, "??: %s", config); } diff --git a/src/helpers/CommonCLI.h b/src/helpers/CommonCLI.h index 63d20c043..7bee051b3 100644 --- a/src/helpers/CommonCLI.h +++ b/src/helpers/CommonCLI.h @@ -69,6 +69,7 @@ public: uint8_t path_hash_mode = 0; // which path mode to use when sending uint8_t loop_detect = 0; uint8_t cad_enabled = 0; // hardware Channel Activity Detection before TX (boolean) + uint8_t extra_sf[4]; // NOTE: observer settings (MQTT/WiFi/timezone/SNMP/alert) are not in NodePrefs. // They live in MQTTPrefs, persisted separately to /mqtt_prefs, so this struct @@ -314,6 +315,12 @@ public: return false; // CommonCLI reports unsupported if not overridden by wrapper }; + #if defined(USE_LR2021) + virtual bool configSideDetectors(const uint8_t sideDetSFs[], uint8_t num, float bw) { + return false; // Override in wrapper + } + #endif + // Fault-alert channel hooks (see NodePrefs::alert_*). The default no-op // implementations keep CLI commands harmless on builds that don't wire up // an AlertReporter. diff --git a/src/helpers/radiolib/CustomLR2021.h b/src/helpers/radiolib/CustomLR2021.h new file mode 100644 index 000000000..17944ef00 --- /dev/null +++ b/src/helpers/radiolib/CustomLR2021.h @@ -0,0 +1,76 @@ +#pragma once + +#include +#include "MeshCore.h" + +class CustomLR2021 : public LR2021 { + bool _rx_boosted = false; + + public: + CustomLR2021(Module *mod) : LR2021(mod) { irqDioNum = LR2021_IRQ_DIO; } + + bool std_init(SPIClass* spi = NULL) + { + + #ifdef LR2021_TCXO_VOLTAGE + float tcxo = LR2021_TCXO_VOLTAGE; + #else + float tcxo = 1.6f; + #endif + + #ifdef LORA_CR + uint8_t cr = LORA_CR; + #else + uint8_t cr = 5; + #endif + + #if defined(P_LORA_SCLK) + #ifdef NRF52_PLATFORM + if (spi) { spi->setPins(P_LORA_MISO, P_LORA_SCLK, P_LORA_MOSI); spi->begin(); } + #elif defined(RP2040_PLATFORM) + if (spi) { + spi->setMISO(P_LORA_MISO); + //spi->setCS(P_LORA_NSS); // Setting CS results in freeze + spi->setSCK(P_LORA_SCLK); + spi->setMOSI(P_LORA_MOSI); + spi->begin(); + } + #else + if (spi) spi->begin(P_LORA_SCLK, P_LORA_MISO, P_LORA_MOSI); + #endif + #endif + int status = begin(LORA_FREQ, LORA_BW, LORA_SF, cr, RADIOLIB_LR2021_LORA_SYNC_WORD_PRIVATE, LORA_TX_POWER, 16, tcxo); + // if radio init fails with -707/-706, try again with tcxo voltage set to 0.0f + if (status == RADIOLIB_ERR_SPI_CMD_FAILED || status == RADIOLIB_ERR_SPI_CMD_INVALID) { + tcxo = 0.0f; + status = begin(LORA_FREQ, LORA_BW, LORA_SF, cr, RADIOLIB_LR2021_LORA_SYNC_WORD_PRIVATE, LORA_TX_POWER, 16, tcxo); + } + if (status != RADIOLIB_ERR_NONE) { + Serial.print("ERROR: radio init failed: "); + Serial.println(status); + return false; // fail + } + + setCRC(2); + explicitHeader(); + + + #ifdef LR2021_RX_BOOSTED_GAIN + setRxBoostedGainMode(LR2021_RX_BOOSTED_GAIN); + #endif + + return true; // success + } + + float getFreqMHz() const { return freqMHz; } + + bool getRxBoostedGainMode() const { return _rx_boosted; } + + bool isReceiving() { + uint32_t irq = getIrqStatus(); + bool detected = ((irq & RADIOLIB_LR2021_IRQ_SYNCWORD_VALID) || (irq & RADIOLIB_LR2021_IRQ_PREAMBLE_DETECTED)); + return detected; + } + + uint8_t getSpreadingFactor() const { return spreadingFactor; } +}; \ No newline at end of file diff --git a/src/helpers/radiolib/CustomLR2021Wrapper.h b/src/helpers/radiolib/CustomLR2021Wrapper.h new file mode 100644 index 000000000..879898315 --- /dev/null +++ b/src/helpers/radiolib/CustomLR2021Wrapper.h @@ -0,0 +1,107 @@ +#pragma once + +#include "CustomLR2021.h" +#include "RadioLibWrappers.h" + +#ifndef USE_LR2021 +#define USE_LR2021 +#endif + +#ifndef LR2021_RX_BOOST_LEVEL +#define LR2021_RX_BOOST_LEVEL 7 +#endif + +class CustomLR2021Wrapper : public RadioLibWrapper { +public: + CustomLR2021Wrapper(CustomLR2021& radio, mesh::MainBoard& board) : RadioLibWrapper(radio, board) { } + + void setParams(float freq, float bw, uint8_t sf, uint8_t cr) override { + ((CustomLR2021 *)_radio)->setFrequency(freq); + ((CustomLR2021 *)_radio)->setSpreadingFactor(sf); + ((CustomLR2021 *)_radio)->setBandwidth(bw); + ((CustomLR2021 *)_radio)->setCodingRate(cr); + updatePreamble(sf); + applySideDetectorConfig(); + } + + bool configSideDetectors(const uint8_t* sideDetSFs, uint8_t num, float bw) override { + LR2021LoRaSideDetector_t tmp[3]; + uint8_t sf = getSpreadingFactor(); + + if (sf >= 10 && num > 1) { return false; } // only 1 side detector allowed when primary SF >= 10 + for (int i = 0; i < num; i++) { + if (sideDetSFs[i] > 12 || sideDetSFs[i] < 5) { return false; } // must be valid SF + if (sideDetSFs[i] <= sf) { return false; } // must be < primary SF + if (sideDetSFs[i] > sf + 4) { return false; } // span must not be > 4 + + tmp[i].sf = sideDetSFs[i]; + float tSym = calcTsym(tmp[i].sf, bw); + if (tSym >= 16.0f) { + tmp[i].ldro = true; + } else { + tmp[i].ldro = false; + } + tmp[i].invertIQ = false; + tmp[i].syncWord = 0x12; + } + int16_t status = ((CustomLR2021 *)_radio)->setSideDetector(tmp, num); + RadioLibWrapper::idle(); // trigger startReceive() + MESH_DEBUG_PRINTLN("setSideDetector() returned %d", status); + + if (status == RADIOLIB_ERR_NONE) { + for (int i = 0; i < num; i++) { _sideDet[i] = tmp[i]; } + _numSideDet = num; + } else { + return false; + } + + return true; + } + + int16_t applySideDetectorConfig() { + int16_t status = ((CustomLR2021 *)_radio)->setSideDetector(_sideDet, _numSideDet); + RadioLibWrapper::idle(); // trigger startReceive() + return status; + } + + float calcTsym(uint8_t sf, float bw) { + float tSym = (float)(uint32_t(1) << sf) / (float)bw; + return tSym; + } + + bool isReceivingPacket() override { + return ((CustomLR2021 *)_radio)->isReceiving(); + } + + float getCurrentRSSI() override { + float rssi = -110; + ((CustomLR2021 *)_radio)->getRssiInst(&rssi); + return rssi; + } + + void onSendFinished() override { + RadioLibWrapper::onSendFinished(); + _radio->setPreambleLength(preambleLengthForSF(getSpreadingFactor())); // overcomes weird issues with small and big pkts + } + + float getLastRSSI() const override { return ((CustomLR2021 *)_radio)->getRSSI(); } + float getLastSNR() const override { return ((CustomLR2021 *)_radio)->getSNR(); } + + uint8_t getSpreadingFactor() const override { return ((CustomLR2021 *)_radio)->getSpreadingFactor(); } + + bool setRxBoostedGainMode(bool en) override { + ((CustomLR2021 *)_radio)->standby(); // LR2021 must be in standby to accept setRxBoostedGainMode + int16_t status = ((CustomLR2021 *)_radio)->setRxBoostedGainMode(en ? LR2021_RX_BOOST_LEVEL: 0); + RadioLibWrapper::idle(); // trigger startReceive() + return status == RADIOLIB_ERR_NONE; + } + + bool getRxBoostedGainMode() const override { + return ((CustomLR2021 *)_radio)->getRxBoostedGainMode(); + } + + protected: + LR2021LoRaSideDetector_t _sideDet[3]; + size_t _numSideDet = 0; + +}; diff --git a/src/helpers/radiolib/RadioLibWrappers.cpp b/src/helpers/radiolib/RadioLibWrappers.cpp index f5a6da9f0..f2af3bce8 100644 --- a/src/helpers/radiolib/RadioLibWrappers.cpp +++ b/src/helpers/radiolib/RadioLibWrappers.cpp @@ -105,6 +105,9 @@ void RadioLibWrapper::loop() { } void RadioLibWrapper::startRecv() { + #if defined(USE_LR2021) + _radio->standby(); // without this LR2021 can throw -706 when calling startReceive after hardware CAD when side detectors are enabled + #endif int err = _radio->startReceive(); if (err == RADIOLIB_ERR_NONE) { state = STATE_RX; @@ -135,7 +138,11 @@ int RadioLibWrapper::recvRaw(uint8_t* bytes, int sz) { last_recv_millis = millis(); } } + #if defined(USE_LR2021) + state = STATE_RX; // LR2021 stays in Rx after readData, calling startReceive while still in Rx throws -706 errors + #else state = STATE_IDLE; // need another startReceive() + #endif } if (state != STATE_RX) { diff --git a/src/helpers/radiolib/RadioLibWrappers.h b/src/helpers/radiolib/RadioLibWrappers.h index a13fd5f32..38104fbaa 100644 --- a/src/helpers/radiolib/RadioLibWrappers.h +++ b/src/helpers/radiolib/RadioLibWrappers.h @@ -88,6 +88,8 @@ public: virtual bool setRxBoostedGainMode(bool) { return false; } virtual bool getRxBoostedGainMode() const { return false; } + + virtual bool configSideDetectors(const uint8_t sideDetSFs[], uint8_t num, float bw) { return false; } }; /** diff --git a/src/helpers/ui/DRV2605Vibration.cpp b/src/helpers/ui/DRV2605Vibration.cpp new file mode 100644 index 000000000..3a42bb884 --- /dev/null +++ b/src/helpers/ui/DRV2605Vibration.cpp @@ -0,0 +1,47 @@ +#ifdef HAS_DRV2605 + +#include "DRV2605Vibration.h" +#include + +void DRV2605Vibration::begin() { +#ifdef PIN_DRV_EN + pinMode(PIN_DRV_EN, OUTPUT); + digitalWrite(PIN_DRV_EN, HIGH); // power up the haptic driver + delay(10); +#endif + if (!drv.begin(&Wire)) { + return; // no haptic driver found, stay silent + } +#ifdef DRV2605_USE_LRA + // LRA mode: 4x brake factor, medium loop gain, back-EMF gain 2 + drv.writeRegister8(DRV2605_REG_FEEDBACK, 0xB6); +#endif + drv.selectLibrary(1); + drv.setMode(DRV2605_MODE_INTTRIG); + _ready = true; +} + +void DRV2605Vibration::trigger(bool force) { + if (!_ready || _quiet) return; + unsigned long now = millis(); + if (!force && _last_trigger != 0 && now - _last_trigger < VIBRATION_TIMEOUT) return; + _last_trigger = now; + drv.setWaveform(0, DRV2605_EFFECT); + drv.setWaveform(1, 0); // pause + drv.setWaveform(2, DRV2605_EFFECT); + drv.setWaveform(3, 0); // end of sequence + drv.go(); +} + +void DRV2605Vibration::loop() { +} + +bool DRV2605Vibration::isVibrating() { + return false; // effects are short, treat as instantaneous +} + +void DRV2605Vibration::stop() { + if (_ready) drv.stop(); +} + +#endif // ifdef HAS_DRV2605 diff --git a/src/helpers/ui/DRV2605Vibration.h b/src/helpers/ui/DRV2605Vibration.h new file mode 100644 index 000000000..a40894be1 --- /dev/null +++ b/src/helpers/ui/DRV2605Vibration.h @@ -0,0 +1,39 @@ +#pragma once + +#ifdef HAS_DRV2605 + +#include +#include + +/* + * Vibration control class for boards where the motor is behind a + * DRV2605 haptic driver on I2C (e.g. Seeed SenseCAP MeshTracker X1). + * Same interface as GenericVibration. + */ + +#ifndef VIBRATION_TIMEOUT +#define VIBRATION_TIMEOUT 5000 // cooldown between vibrations +#endif + +#ifndef DRV2605_EFFECT +#define DRV2605_EFFECT 16 // "1000 ms alert" from the DRV2605 effect library +#endif + +class DRV2605Vibration { +public: + void begin(); // power up and init the DRV2605 + void trigger(bool force = false); // trigger vibration; force skips the cooldown + void loop(); // no-op, the DRV2605 plays effects autonomously + bool isVibrating(); + void stop(); // stop vibration immediately + void quiet(bool q) { _quiet = q; } + bool isQuiet() const { return _quiet; } + +private: + Adafruit_DRV2605 drv; + bool _ready = false; + bool _quiet = false; + unsigned long _last_trigger = 0; +}; + +#endif // ifdef HAS_DRV2605 diff --git a/variants/lilygo_techo_card/platformio.ini b/variants/lilygo_techo_card/platformio.ini index 4ebf43da9..17ba8d1b2 100644 --- a/variants/lilygo_techo_card/platformio.ini +++ b/variants/lilygo_techo_card/platformio.ini @@ -119,3 +119,8 @@ lib_deps = ${LilyGo_T-Echo_Card.lib_deps} end2endzone/NonBlockingRTTTL@^1.3.0 densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo_Card_kiss_modem] +extends = LilyGo_T-Echo_Card +build_src_filter = ${LilyGo_T-Echo_Card.build_src_filter} + +<../examples/kiss_modem/> diff --git a/variants/lilygo_techo_lite/platformio.ini b/variants/lilygo_techo_lite/platformio.ini index 9ec73d59a..1a8ad6772 100644 --- a/variants/lilygo_techo_lite/platformio.ini +++ b/variants/lilygo_techo_lite/platformio.ini @@ -12,10 +12,9 @@ build_flags = ${nrf52_base.build_flags} -D WRAPPER_CLASS=CustomSX1262Wrapper -D LORA_TX_POWER=22 -D SX126X_POWER_EN=30 - -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 -D SX126X_CURRENT_LIMIT=140 -D SX126X_RX_BOOSTED_GAIN=1 - -D SX126X_USE_REGULATOR_LDO=1 -D P_LORA_TX_LED=LED_GREEN -D DISABLE_DIAGNOSTIC_OUTPUT -D ENV_INCLUDE_GPS=1 @@ -117,7 +116,7 @@ build_flags = -D WRAPPER_CLASS=CustomSX1262Wrapper -D LORA_TX_POWER=22 -D SX126X_POWER_EN=30 - -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 -D SX126X_CURRENT_LIMIT=140 -D SX126X_RX_BOOSTED_GAIN=1 -D P_LORA_TX_LED=LED_GREEN @@ -162,6 +161,7 @@ build_flags = -D WRAPPER_CLASS=CustomSX1262Wrapper -D LORA_TX_POWER=22 -D SX126X_POWER_EN=30 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 -D SX126X_CURRENT_LIMIT=140 -D SX126X_RX_BOOSTED_GAIN=1 -D P_LORA_TX_LED=LED_GREEN diff --git a/variants/lilygo_techo_lite/variant.h b/variants/lilygo_techo_lite/variant.h index 702ab3349..38b79c66d 100644 --- a/variants/lilygo_techo_lite/variant.h +++ b/variants/lilygo_techo_lite/variant.h @@ -105,12 +105,14 @@ #define LORA_CS _PINNUM(0, 11) #define SX126X_POWER_EN _PINNUM(0, 30) #define SX126X_DIO1 _PINNUM(1, 8) +#define SX126X_DIO2 _PINNUM(0, 5) #define SX126X_BUSY _PINNUM(0, 14) #define SX126X_RESET _PINNUM(0, 7) #define SX126X_RXEN _PINNUM(1, 1) #define SX126X_TXEN _PINNUM(0, 27) #define P_LORA_DIO_1 SX126X_DIO1 +#define P_LORA_DIO_2 SX126X_DIO2 #define P_LORA_NSS LORA_CS #define P_LORA_RESET SX126X_RESET #define P_LORA_BUSY SX126X_BUSY diff --git a/variants/lilygo_teth_elite/platformio.ini b/variants/lilygo_teth_elite/platformio.ini index ee1b98795..2debb0396 100644 --- a/variants/lilygo_teth_elite/platformio.ini +++ b/variants/lilygo_teth_elite/platformio.ini @@ -98,3 +98,8 @@ build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} lib_deps = ${LilyGo_TETH_Elite_sx1262.lib_deps} densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TETH_Elite_sx1262_kiss_modem] +extends = LilyGo_TETH_Elite_sx1262 +build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} + +<../examples/kiss_modem/> diff --git a/variants/meshnology_w12/MeshnologyW12Board.cpp b/variants/meshnology_w12/MeshnologyW12Board.cpp new file mode 100644 index 000000000..25c0d4f1a --- /dev/null +++ b/variants/meshnology_w12/MeshnologyW12Board.cpp @@ -0,0 +1,83 @@ +#include "MeshnologyW12Board.h" + +void MeshnologyW12Board::begin() { + ESP32Board::begin(); + + pinMode(PIN_ADC_CTRL, OUTPUT); + digitalWrite(PIN_ADC_CTRL, LOW); // Disable battery sense until required + + pinMode(P_LORA_LF_PA_POWER, OUTPUT); + digitalWrite(P_LORA_LF_PA_POWER, HIGH); // PA_EN_M — power the GC1109 FEM + + pinMode(P_LORA_HF_PA_POWER, OUTPUT); + digitalWrite(P_LORA_HF_PA_POWER, LOW); // PA_EN_G — disable the 2.4GHz FEM + + delay(100); // give the GC1109 some time to start + + periph_power.begin(); + esp_reset_reason_t reason = esp_reset_reason(); + if (reason == ESP_RST_DEEPSLEEP) { + long wakeup_source = esp_sleep_get_ext1_wakeup_status(); + if (wakeup_source & (1 << P_LORA_DIO_1)) { // received a LoRa packet (while in deep sleep) + startup_reason = BD_STARTUP_RX_PACKET; + } + + rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS); + rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1); + } + } + + void MeshnologyW12Board::onBeforeTransmit(void) { + neopixelWrite(NEOPIXEL_LED, NEOPIXEL_BRIGHTNESS, NEOPIXEL_BRIGHTNESS, NEOPIXEL_BRIGHTNESS); // turn TX neopixel on (White) + } + + void MeshnologyW12Board::onAfterTransmit(void) { + neopixelWrite(NEOPIXEL_LED, 0, 0, 0); // turn TX neopixel off + } + + void MeshnologyW12Board::enterDeepSleep(uint32_t secs, int pin_wake_btn) { + esp_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_ON); + + // Make sure the DIO1 and NSS GPIOs are hold on required levels during deep sleep + rtc_gpio_set_direction((gpio_num_t)P_LORA_DIO_1, RTC_GPIO_MODE_INPUT_ONLY); + rtc_gpio_pulldown_en((gpio_num_t)P_LORA_DIO_1); + + rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS); + + if (pin_wake_btn < 0) { + esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet + } else { + esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1) | (1L << pin_wake_btn), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet OR wake btn + } + + if (secs > 0) { + esp_sleep_enable_timer_wakeup(secs * 1000000); + } + + // Finally set ESP32 into sleep + esp_deep_sleep_start(); // CPU halts here and never returns! + } + + void MeshnologyW12Board::powerOff() { + enterDeepSleep(0); + } + + uint16_t MeshnologyW12Board::getBattMilliVolts() { + analogReadResolution(12); + analogSetAttenuation(ADC_11db); + digitalWrite(PIN_ADC_CTRL, HIGH); + delay(10); + uint32_t raw = 0; + for (int i = 0; i < 8; i++) { + raw += analogRead(PIN_VBAT_READ); + } + raw = raw / 8; + + digitalWrite(PIN_ADC_CTRL, LOW); + + return (adc_mult * (3.3 / 4096.0) * raw) * 1000; + } + + const char* MeshnologyW12Board::getManufacturerName() const { + return "Meshnology W12"; + } \ No newline at end of file diff --git a/variants/meshnology_w12/MeshnologyW12Board.h b/variants/meshnology_w12/MeshnologyW12Board.h new file mode 100644 index 000000000..85bec9904 --- /dev/null +++ b/variants/meshnology_w12/MeshnologyW12Board.h @@ -0,0 +1,37 @@ +#pragma once + +#include +#include +#include +#include + +#ifndef ADC_MULTIPLIER + #define ADC_MULTIPLIER 5.42 +#endif + +class MeshnologyW12Board : public ESP32Board { + +protected: + float adc_mult = ADC_MULTIPLIER; + +public: + RefCountedDigitalPin periph_power; + MeshnologyW12Board() : periph_power(PIN_VEXT_EN, PIN_VEXT_EN_ACTIVE) { } + + void begin(); + void onBeforeTransmit(void) override; + void onAfterTransmit(void) override; + void enterDeepSleep(uint32_t secs, int pin_wake_btn = -1); + void powerOff() override; + uint16_t getBattMilliVolts() override; + bool setAdcMultiplier(float multiplier) override { + if (multiplier == 0.0f) { + adc_mult = ADC_MULTIPLIER; + } else { + adc_mult = multiplier; + } + return true; + } + float getAdcMultiplier() const override { return adc_mult; } + const char* getManufacturerName() const override; +}; diff --git a/variants/meshnology_w12/pins_arduino.h b/variants/meshnology_w12/pins_arduino.h new file mode 100644 index 000000000..5cfb36970 --- /dev/null +++ b/variants/meshnology_w12/pins_arduino.h @@ -0,0 +1,69 @@ +#ifndef Pins_Arduino_h +#define Pins_Arduino_h + +#include + +static const uint8_t LED_BUILTIN = -1; +#define BUILTIN_LED LED_BUILTIN // backward compatibility +#define LED_BUILTIN LED_BUILTIN // allow testing #ifdef LED_BUILTIN + +static const uint8_t TX = 43; +static const uint8_t RX = 44; + +static const uint8_t SDA = 3; +static const uint8_t SCL = 4; + +static const uint8_t SS = 8; +static const uint8_t MOSI = 10; +static const uint8_t MISO = 11; +static const uint8_t SCK = 9; + +static const uint8_t A0 = 1; +static const uint8_t A1 = 2; +static const uint8_t A2 = 3; +static const uint8_t A3 = 4; +static const uint8_t A4 = 5; +static const uint8_t A5 = 6; +static const uint8_t A6 = 7; +static const uint8_t A7 = 8; +static const uint8_t A8 = 9; +static const uint8_t A9 = 10; +static const uint8_t A10 = 11; +static const uint8_t A11 = 12; +static const uint8_t A12 = 13; +static const uint8_t A13 = 14; +static const uint8_t A14 = 15; +static const uint8_t A15 = 16; +static const uint8_t A16 = 17; +static const uint8_t A17 = 18; +static const uint8_t A18 = 19; +static const uint8_t A19 = 20; + +static const uint8_t T1 = 1; +static const uint8_t T2 = 2; +static const uint8_t T3 = 3; +static const uint8_t T4 = 4; +static const uint8_t T5 = 5; +static const uint8_t T6 = 6; +static const uint8_t T7 = 7; +static const uint8_t T8 = 8; +static const uint8_t T9 = 9; +static const uint8_t T10 = 10; +static const uint8_t T11 = 11; +static const uint8_t T12 = 12; +static const uint8_t T13 = 13; +static const uint8_t T14 = 14; + +static const uint8_t Vext = 45; +static const uint8_t LED = -1; +static const uint8_t RST_OLED = 21; +static const uint8_t SCL_OLED = 18; +static const uint8_t SDA_OLED = 17; + +static const uint8_t RST_LoRa = 12; +static const uint8_t BUSY_LoRa = 13; +static const uint8_t DIO0 = 14; + + + +#endif /* Pins_Arduino_h */ \ No newline at end of file diff --git a/variants/meshnology_w12/platformio.ini b/variants/meshnology_w12/platformio.ini new file mode 100644 index 000000000..1168f10a0 --- /dev/null +++ b/variants/meshnology_w12/platformio.ini @@ -0,0 +1,216 @@ +[meshnology_w12] +extends = esp32_base +board = meshnology_w12 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/meshnology_w12 + -D MESHNOLOGY_W12 + -D ESP32_CPU_FREQ=80 + -D RADIO_CLASS=CustomLR2021 + -D WRAPPER_CLASS=CustomLR2021Wrapper + -D USE_LR2021 + -D NEOPIXEL_LED=46 + -D NEOPIXEL_BRIGHTNESS=64 + -D P_LORA_DIO_1=14 + -D LR2021_IRQ_DIO=8 ; GPIO14 is connected to LR2021 DIO8 + -D P_LORA_NSS=8 + -D P_LORA_SCLK=9 + -D P_LORA_MOSI=10 + -D P_LORA_MISO=11 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D LR2021_TCXO_VOLTAGE=0.0f ; this board has no tcxo + -D RF_SWITCH_TABLE ; used below in commented code for the RF switch table. + -D P_LORA_LF_PA_POWER=4 ; PA_EN_M - power enable for the GC1109 868/915 PA + -D P_LORA_HF_PA_POWER=3 ; PA_EN_G - power enable for RFX2402E 2.4G PA + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=45 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D LORA_TX_POWER=4 + -D MAX_LORA_TX_POWER=4 ; GC1109 datasheet says max input at TX port is +5dbm, confirmed full saturation seems to occur at around 3-4dbm + -D PIN_GPS_RX=38 + -D PIN_GPS_TX=39 + -D PIN_GPS_RESET=42 + -D PIN_GPS_RESET_ACTIVE=LOW + -D PIN_GPS_EN=48 + -D PIN_GPS_EN_ACTIVE=LOW + ; -D ENV_INCLUDE_GPS=1 + -D PIN_VBAT_READ=1 + -D PIN_ADC_CTRL=2 + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D PIN_RESET=47 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/meshnology_w12> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:meshnology_w12_repeater] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Meshnology W12 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:meshnology_w12_repeater_bridge_espnow] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 + ; -D BRIDGE_DEBUG=1 + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + +[env:meshnology_w12_room_server] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Meshnology W12 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + +[env:meshnology_w12_terminal_chat] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_companion_radio_usb] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display +; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1 +; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_companion_radio_ble] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D BLE_PIN_CODE=123456 ; dynamic, random PIN + ; -D AUTO_SHUTDOWN_MILLIVOLTS=3400 ; disabled by default, otherwise reading bounce causes shutdown when there's no battery connected. + ; -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_companion_radio_wifi] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SSD1306Display + ; -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_sensor] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D ADVERT_NAME='"Meshnology W12 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=3 + -D ENV_PIN_SCL=4 + -D DISPLAY_CLASS=SSD1306Display + ; -D MESH_PACKET_LOGGING=1 + ; -D MESH_DEBUG=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + +[env:meshnology_w12_kiss_modem] +extends = meshnology_w12 +build_src_filter = ${meshnology_w12.build_src_filter} + +<../examples/kiss_modem/> diff --git a/variants/meshnology_w12/target.cpp b/variants/meshnology_w12/target.cpp new file mode 100644 index 000000000..bf04ba364 --- /dev/null +++ b/variants/meshnology_w12/target.cpp @@ -0,0 +1,73 @@ +#include +#include "target.h" + +MeshnologyW12Board board; + +#if defined(P_LORA_SCLK) + static SPIClass spi; + RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, spi); +#else + RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY); +#endif + +WRAPPER_CLASS radio_driver(radio, board); + +ESP32RTCClock fallback_clock; +AutoDiscoverRTCClock rtc_clock(fallback_clock); + +#if ENV_INCLUDE_GPS + #include + MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1, &rtc_clock); + EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea); +#else + EnvironmentSensorManager sensors; +#endif + +#ifdef DISPLAY_CLASS + DISPLAY_CLASS display(NULL); + MomentaryButton user_btn(PIN_USER_BTN, 1000, true); +#endif + +const uint32_t rfswitch_dios[] = { + RADIOLIB_LR2021_DIO5, // RFX2402E 2.4G_TX_EN + RADIOLIB_LR2021_DIO6, // RFX2402E 2.4G_RX_EN + RADIOLIB_LR2021_DIO9, // GC1109 CTX (Transmit mode) + RADIOLIB_LR2021_DIO10, // GC1109 CPS (Bypass mode) + RADIOLIB_LR2021_DIO11, // GC1109 CSD (Shutdown) +}; + +static const Module::RfSwitchMode_t rfswitch_table[] = { + // DIO5 DIO6 DIO9 DIO10 DIO11 + { LR2021::MODE_STBY, { LOW, LOW, LOW, LOW, LOW } }, // everything off + { LR2021::MODE_RX, { LOW, LOW, LOW, LOW, HIGH } }, // rx_lf: GC1109 LNA + { LR2021::MODE_TX, { LOW, LOW, HIGH, HIGH, HIGH } }, // tx_lf: GC1109 full PA + { LR2021::MODE_RX_HF, { LOW, HIGH, LOW, LOW, LOW } }, // rx_hf: 2G4 LNA, GC1109 off + { LR2021::MODE_TX_HF, { HIGH, LOW, LOW, LOW, LOW } }, // tx_hf: 2G4 PA, GC1109 off + END_OF_MODE_TABLE, +}; + + +bool radio_init() { + fallback_clock.begin(); + rtc_clock.begin(Wire); + +#if defined(P_LORA_SCLK) + int err = radio.std_init(&spi); + if (err != 1) return err; +#else + int err = radio.std_init(); + if (err != 1) return err; +#endif + +#ifdef RF_SWITCH_TABLE + radio.setRfSwitchTable(rfswitch_dios, rfswitch_table); +#endif + + return true; +} + +mesh::LocalIdentity radio_new_identity() { + RadioNoiseListener rng(radio); + return mesh::LocalIdentity(&rng); // create new random identity +} + diff --git a/variants/meshnology_w12/target.h b/variants/meshnology_w12/target.h new file mode 100644 index 000000000..1bf8876b2 --- /dev/null +++ b/variants/meshnology_w12/target.h @@ -0,0 +1,28 @@ +#pragma once + +#define RADIOLIB_STATIC_ONLY 1 +#include +#include +#include +#include +#include +#include +#include +#ifdef DISPLAY_CLASS + #include + #include +#endif + +extern MeshnologyW12Board board; +extern WRAPPER_CLASS radio_driver; +extern AutoDiscoverRTCClock rtc_clock; +extern EnvironmentSensorManager sensors; + +#ifdef DISPLAY_CLASS + extern DISPLAY_CLASS display; + extern MomentaryButton user_btn; +#endif + +bool radio_init(); +mesh::LocalIdentity radio_new_identity(); + diff --git a/variants/meshtracker_x1/MeshTrackerX1Board.cpp b/variants/meshtracker_x1/MeshTrackerX1Board.cpp new file mode 100644 index 000000000..56e537a23 --- /dev/null +++ b/variants/meshtracker_x1/MeshTrackerX1Board.cpp @@ -0,0 +1,23 @@ +#include +#include + +#include "MeshTrackerX1Board.h" + +void MeshTrackerX1Board::begin() { + NRF52BoardDCDC::begin(); + btn_prev_state = LOW; // button is active HIGH + +#ifdef BUTTON_PIN + pinMode(BATTERY_PIN, INPUT); + pinMode(BUTTON_PIN, INPUT_PULLDOWN); + pinMode(LED_PIN, OUTPUT); +#endif + +#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL) + Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL); +#endif + + Wire.begin(); + + delay(10); // give lr2021 some time to power up +} diff --git a/variants/meshtracker_x1/MeshTrackerX1Board.h b/variants/meshtracker_x1/MeshTrackerX1Board.h new file mode 100644 index 000000000..51f022e0b --- /dev/null +++ b/variants/meshtracker_x1/MeshTrackerX1Board.h @@ -0,0 +1,87 @@ +#pragma once + +#include +#include +#include + +class MeshTrackerX1Board : public NRF52BoardDCDC { +protected: + uint8_t btn_prev_state; + +public: + MeshTrackerX1Board() : NRF52Board("X1_OTA") {} + void begin(); + + uint16_t getBattMilliVolts() override { + #ifdef BATTERY_PIN + #ifdef PIN_BAT_ADC_EN + digitalWrite(PIN_BAT_ADC_EN, HIGH); + #endif + analogReference(AR_INTERNAL_3_0); + analogReadResolution(12); + delay(10); + float volts = (analogRead(BATTERY_PIN) * ADC_MULTIPLIER * AREF_VOLTAGE) / 4096; + + analogReference(AR_DEFAULT); // put back to default + analogReadResolution(10); + + return volts * 1000; + #else + return 0; + #endif + } + + const char* getManufacturerName() const override { + return "Seeed SenseCAP MeshTracker X1"; + } + + int buttonStateChanged() { + #ifdef BUTTON_PIN + uint8_t v = digitalRead(BUTTON_PIN); + if (v != btn_prev_state) { + btn_prev_state = v; + return (v == USER_BTN_PRESSED) ? 1 : -1; + } + #endif + return 0; + } + + void powerOff() override { + #ifdef HAS_GPS + digitalWrite(GPS_VRTC_EN, LOW); + digitalWrite(GPS_RESET, LOW); + digitalWrite(GPS_SLEEP_INT, LOW); + digitalWrite(GPS_RTC_INT, LOW); + digitalWrite(GPS_EN, LOW); + #endif + + #ifdef PIN_DRV_EN + digitalWrite(PIN_DRV_EN, LOW); + #endif + + #ifdef PIN_BAT_ADC_EN + digitalWrite(PIN_BAT_ADC_EN, LOW); + #endif + + #ifdef PIN_3V3_EN + digitalWrite(PIN_3V3_EN, LOW); + #endif + + // set led on and wait for button release before poweroff + #ifdef LED_PIN + digitalWrite(LED_PIN, HIGH); + #endif + #ifdef BUTTON_PIN + while(digitalRead(BUTTON_PIN)); + #endif + #ifdef LED_PIN + digitalWrite(LED_PIN, LOW); + #endif + + #ifdef BUTTON_PIN + nrf_gpio_cfg_sense_input(BUTTON_PIN, NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH); + #endif + + sd_power_system_off(); + } +}; diff --git a/variants/meshtracker_x1/platformio.ini b/variants/meshtracker_x1/platformio.ini new file mode 100644 index 000000000..2194d48d9 --- /dev/null +++ b/variants/meshtracker_x1/platformio.ini @@ -0,0 +1,137 @@ +[MeshTracker_X1] +extends = nrf52_base +board = seeed-mesh-tracker-x1 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/meshtracker_x1 + -I src/helpers/ui + -D MESH_TRACKER_X1 + -D PIN_USER_BTN=6 + -D USER_BTN_PRESSED=HIGH + -D PIN_STATUS_LED=24 + -D PIN_STATUS_LED_R=3 ; P0.3 red + -D PIN_STATUS_LED_G=24 ; P0.24 green + -D PIN_STATUS_LED_B=28 ; P0.28 blue + -D RADIO_CLASS=CustomLR2021 + -D USE_LR2021 + -D WRAPPER_CLASS=CustomLR2021Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_BUSY=7 ; P0.7 + -D P_LORA_SCLK=11 ; P0.11 + -D P_LORA_NSS=12 ; P0.12 + -D P_LORA_DIO_1=33 ; P1.1 + -D P_LORA_MISO=40 ; P1.8 + -D P_LORA_MOSI=41 ; P1.9 + -D P_LORA_RESET=42 ; P1.10 + -D LR2021_IRQ_DIO=8 ; P1.1 is connected to LR2021 DIO8 + -D LR2021_TCXO_VOLTAGE=1.6f + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/meshtracker_x1> +lib_deps = ${nrf52_base.lib_deps} + https://github.com/adafruit/Adafruit_SPA06_003/archive/refs/tags/1.0.2.zip +debug_tool = jlink +upload_protocol = nrfutil + +[env:MeshTracker_X1_repeater] +extends = MeshTracker_X1 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"MeshTracker X1 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +; -D MESH_PACKET_LOGGING=1 +; -D MESH_DEBUG=1 +build_src_filter = ${MeshTracker_X1.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${MeshTracker_X1.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:MeshTracker_X1_room_server] +extends = MeshTracker_X1 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"MeshTracker X1 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +; -D MESH_PACKET_LOGGING=1 +; -D MESH_DEBUG=1 +build_src_filter = ${MeshTracker_X1.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${MeshTracker_X1.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:MeshTracker_X1_companion_radio_usb] +extends = MeshTracker_X1 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D QSPIFLASH=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 +; -D MESH_PACKET_LOGGING=1 +; -D MESH_DEBUG=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=25 + -D HAS_DRV2605=1 + -D DRV2605_USE_LRA=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${MeshTracker_X1.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${MeshTracker_X1.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit DRV2605 Library @ ^1.2.4 + +[env:MeshTracker_X1_companion_radio_ble] +extends = MeshTracker_X1 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D QSPIFLASH=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_TX_POWER=0 +; -D BLE_DEBUG_LOGGING=1 +; -D MESH_PACKET_LOGGING=1 +; -D MESH_DEBUG=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=25 + -D HAS_DRV2605=1 + -D DRV2605_USE_LRA=1 + -D ADVERT_NAME='"@@MAC"' +build_src_filter = ${MeshTracker_X1.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${MeshTracker_X1.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit DRV2605 Library @ ^1.2.4 + +[env:MeshTracker_X1_kiss_modem] +extends = MeshTracker_X1 +build_src_filter = ${MeshTracker_X1.build_src_filter} + +<../examples/kiss_modem/> diff --git a/variants/meshtracker_x1/target.cpp b/variants/meshtracker_x1/target.cpp new file mode 100644 index 000000000..d6d548b51 --- /dev/null +++ b/variants/meshtracker_x1/target.cpp @@ -0,0 +1,132 @@ +#include +#include "target.h" +#include + +MeshTrackerX1Board board; + +RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, SPI); + +WRAPPER_CLASS radio_driver(radio, board); + +VolatileRTCClock rtc_clock; +MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1, &rtc_clock); +MeshTrackerX1SensorManager sensors = MeshTrackerX1SensorManager(nmea); + +#ifdef DISPLAY_CLASS + NullDisplayDriver display; +#endif + +bool radio_init() { + return radio.std_init(&SPI); +} + +mesh::LocalIdentity radio_new_identity() { + RadioNoiseListener rng(radio); + return mesh::LocalIdentity(&rng); // create new random identity +} + +void MeshTrackerX1SensorManager::start_gps() { + gps_active = true; + // this init sequence comes from seeed examples and deals with all gps pins + pinMode(GPS_EN, OUTPUT); + digitalWrite(GPS_EN, HIGH); + delay(10); + pinMode(GPS_VRTC_EN, OUTPUT); + digitalWrite(GPS_VRTC_EN, HIGH); + delay(10); + + pinMode(GPS_RESET, OUTPUT); + digitalWrite(GPS_RESET, HIGH); + delay(10); + digitalWrite(GPS_RESET, LOW); + + pinMode(GPS_SLEEP_INT, OUTPUT); + digitalWrite(GPS_SLEEP_INT, HIGH); + pinMode(GPS_RTC_INT, OUTPUT); + digitalWrite(GPS_RTC_INT, LOW); +} + +void MeshTrackerX1SensorManager::sleep_gps() { + gps_active = false; + digitalWrite(GPS_VRTC_EN, HIGH); // keep RTC alive for faster fix on wake + digitalWrite(GPS_EN, LOW); + digitalWrite(GPS_RESET, LOW); + digitalWrite(GPS_SLEEP_INT, HIGH); + digitalWrite(GPS_RTC_INT, LOW); +} + +void MeshTrackerX1SensorManager::stop_gps() { + gps_active = false; + digitalWrite(GPS_VRTC_EN, LOW); + digitalWrite(GPS_EN, LOW); + digitalWrite(GPS_RESET, LOW); + digitalWrite(GPS_SLEEP_INT, HIGH); + digitalWrite(GPS_RTC_INT, LOW); +} + +bool MeshTrackerX1SensorManager::begin() { + // init GPS + Serial1.begin(GPS_BAUD_RATE); + + // init SPA06-003 barometer + baro_ok = spa06.begin(SPA06_003_DEFAULT_ADDR, &Wire) || spa06.begin(0x76, &Wire); + if (baro_ok) { + spa06.setPressureOversampling(SPA06_003_OVERSAMPLE_8); + spa06.setTemperatureOversampling(SPA06_003_OVERSAMPLE_8); + // 1 Hz continuous keeps reads non-blocking at minimal power cost + spa06.setPressureMeasureRate(SPA06_003_RATE_1); + spa06.setTemperatureMeasureRate(SPA06_003_RATE_1); + spa06.setMeasurementMode(SPA06_003_MEAS_CONTINUOUS_BOTH); + } + return true; +} + +bool MeshTrackerX1SensorManager::querySensors(uint8_t requester_permissions, CayenneLPP& telemetry) { + if (requester_permissions & TELEM_PERM_LOCATION) { // does requester have permission? + telemetry.addGPS(TELEM_CHANNEL_SELF, node_lat, node_lon, node_altitude); + } + if (requester_permissions & TELEM_PERM_ENVIRONMENT && baro_ok) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, spa06.readTemperature()); + telemetry.addBarometricPressure(TELEM_CHANNEL_SELF, spa06.readPressure()); + } + return true; +} + +void MeshTrackerX1SensorManager::loop() { + static long next_gps_update = 0; + + + _nmea->loop(); + + if (millis() > next_gps_update) { + if (gps_active && _nmea->isValid()) { + node_lat = ((double)_nmea->getLatitude())/1000000.; + node_lon = ((double)_nmea->getLongitude())/1000000.; + node_altitude = ((double)_nmea->getAltitude()) / 1000.0; + } + next_gps_update = millis() + 1000; + } +} + +int MeshTrackerX1SensorManager::getNumSettings() const { return 1; } // just one supported: "gps" (power switch) + +const char* MeshTrackerX1SensorManager::getSettingName(int i) const { + return i == 0 ? "gps" : NULL; +} +const char* MeshTrackerX1SensorManager::getSettingValue(int i) const { + if (i == 0) { + return gps_active ? "1" : "0"; + } + return NULL; +} +bool MeshTrackerX1SensorManager::setSettingValue(const char* name, const char* value) { + if (strcmp(name, "gps") == 0) { + if (strcmp(value, "0") == 0) { + sleep_gps(); // sleep for faster fix ! + } else { + start_gps(); + } + return true; + } + return false; // not supported +} diff --git a/variants/meshtracker_x1/target.h b/variants/meshtracker_x1/target.h new file mode 100644 index 000000000..9741efb6a --- /dev/null +++ b/variants/meshtracker_x1/target.h @@ -0,0 +1,47 @@ +#pragma once + +#define RADIOLIB_STATIC_ONLY 1 +#include +#include +#include "MeshTrackerX1Board.h" +#include +#include +#include +#include +#include +#ifdef DISPLAY_CLASS + #include "NullDisplayDriver.h" +#endif + +class MeshTrackerX1SensorManager: public SensorManager { + bool gps_active = false; + bool baro_ok = false; + Adafruit_SPA06_003 spa06; + LocationProvider * _nmea; + + void start_gps(); + void sleep_gps(); + void stop_gps(); +public: + MeshTrackerX1SensorManager(LocationProvider &nmea): _nmea(&nmea) { } + bool begin() override; + bool querySensors(uint8_t requester_permissions, CayenneLPP& telemetry) override; + void loop() override; + int getNumSettings() const override; + const char* getSettingName(int i) const override; + const char* getSettingValue(int i) const override; + bool setSettingValue(const char* name, const char* value) override; + LocationProvider* getLocationProvider() { return _nmea; } +}; + +#ifdef DISPLAY_CLASS + extern NullDisplayDriver display; +#endif + +extern MeshTrackerX1Board board; +extern WRAPPER_CLASS radio_driver; +extern VolatileRTCClock rtc_clock; +extern MeshTrackerX1SensorManager sensors; + +bool radio_init(); +mesh::LocalIdentity radio_new_identity(); diff --git a/variants/meshtracker_x1/variant.cpp b/variants/meshtracker_x1/variant.cpp new file mode 100644 index 000000000..3f38a604d --- /dev/null +++ b/variants/meshtracker_x1/variant.cpp @@ -0,0 +1,109 @@ +/* + * variant.cpp - Seeed SenseCAP MeshTracker X1 (nRF52840 + Semtech LR2021) + */ + +#include "variant.h" +#include "wiring_constants.h" +#include "wiring_digital.h" + +const uint32_t g_ADigitalPinMap[PINS_COUNT + 1] = +{ + 0, // P0.00 + 1, // P0.01 + 2, // P0.02, AIN0 BATTERY_PIN + 3, // P0.03, LED_RED + 4, // P0.04, AIN2 VCC_ADC + 5, // P0.05, AIN3 EXT_PWR_DETECT + 6, // P0.06, PIN_BUTTON1 + 7, // P0.07, LORA_BUSY + 8, // P0.08, GPS_RESET + 9, // P0.09, PIN_RTC_EN + 10, // P0.10 + 11, // P0.11, PIN_SPI_SCK + 12, // P0.12, PIN_SPI_NSS + 13, // P0.13, PIN_SERIAL1_TX + 14, // P0.14, PIN_SERIAL1_RX + 15, // P0.15 + 16, // P0.16, PIN_SERIAL2_TX + 17, // P0.17, PIN_SERIAL2_RX + 18, // P0.18 + 19, // P0.19 + 20, // P0.20 + 21, // P0.21 + 22, // P0.22 + 23, // P0.23 + 24, // P0.24, LED_GREEN + 25, // P0.25, BUZZER_PIN + 26, // P0.26 + 27, // P0.27 + 28, // P0.28, LED_BLUE + 29, // P0.29, GPS_RTC_INT + 30, // P0.30, GPS_SLEEP_INT + 31, // P0.31 + 32, // P1.00 + 33, // P1.01, LORA_DIO_1 (LR2021 DIO8 IRQ) + 34, // P1.02 + 35, // P1.03, EXT_CHRG_DETECT + 36, // P1.04, CHARGE_DONE + 37, // P1.05, PIN_DRV_EN + 38, // P1.06, PIN_BAT_ADC_EN + 39, // P1.07, PIN_3V3_EN + 40, // P1.08, PIN_SPI_MISO + 41, // P1.09, PIN_SPI_MOSI + 42, // P1.10, LORA_RESET + 43, // P1.11, GPS_EN + 44, // P1.12 + 45, // P1.13, GPS_VRTC_EN + 46, // P1.14, PIN_WIRE_SCL + 47, // P1.15, PIN_WIRE_SDA + 255, // NRFX_SPIM_PIN_NOT_USED +}; + +void initVariant() +{ + pinMode(BATTERY_PIN, INPUT); + pinMode(EXT_CHRG_DETECT, INPUT_PULLUP); + pinMode(EXT_PWR_DETECT, INPUT); + pinMode(PIN_BUTTON1, INPUT_PULLDOWN); + + pinMode(PIN_3V3_EN, OUTPUT); + digitalWrite(PIN_3V3_EN, HIGH); + + pinMode(PIN_FLASH_EN, OUTPUT); + digitalWrite(PIN_FLASH_EN, HIGH); + + pinMode(PIN_BAT_ADC_EN, OUTPUT); + digitalWrite(PIN_BAT_ADC_EN, HIGH); + + pinMode(PIN_RTC_EN, OUTPUT); + digitalWrite(PIN_RTC_EN, LOW); + + pinMode(PIN_DRV_EN, OUTPUT); + digitalWrite(PIN_DRV_EN, LOW); + + pinMode(LED_RED, OUTPUT); + digitalWrite(LED_RED, LOW); + + pinMode(LED_GREEN, OUTPUT); + digitalWrite(LED_GREEN, LOW); + + pinMode(LED_BLUE, OUTPUT); + digitalWrite(LED_BLUE, LOW); + + pinMode(GPS_EN, OUTPUT); + digitalWrite(GPS_EN, LOW); + + pinMode(GPS_VRTC_EN, OUTPUT); + digitalWrite(GPS_VRTC_EN, HIGH); + + pinMode(GPS_RESET, OUTPUT); + digitalWrite(GPS_RESET, LOW); + + pinMode(GPS_SLEEP_INT, OUTPUT); + digitalWrite(GPS_SLEEP_INT, HIGH); + + pinMode(GPS_RTC_INT, OUTPUT); + digitalWrite(GPS_RTC_INT, LOW); + + pinMode(BUZZER_PIN, INPUT_PULLDOWN); +} diff --git a/variants/meshtracker_x1/variant.h b/variants/meshtracker_x1/variant.h new file mode 100644 index 000000000..7f2b246b5 --- /dev/null +++ b/variants/meshtracker_x1/variant.h @@ -0,0 +1,139 @@ +/* + * variant.h - Seeed SenseCAP MeshTracker X1 (nRF52840 + Semtech LR2021) + */ + +#pragma once + +#include "WVariant.h" + +//////////////////////////////////////////////////////////////////////////////// +// Low frequency clock source + +#define USE_LFXO // 32.768 kHz crystal oscillator +#define VARIANT_MCK (64000000ul) + +//////////////////////////////////////////////////////////////////////////////// +// Power + +#define NRF_APM // detect usb power +#define PIN_3V3_EN (39) // P1.7 Power to sensors +#define PIN_BAT_ADC_EN (38) // P1.6 Power to battery ADC divider +#define PIN_RTC_EN (9) // P0.9 Power to RTC + +#define BATTERY_PIN (2) // P0.2/AIN0 +#define BATTERY_IMMUTABLE +#define ADC_MULTIPLIER (2.0F) + +#define EXT_CHRG_DETECT (35) // P1.3, LOW while charging +// P1.4 is the charger's second status line, but it reads LOW regardless of +// charge state on this board, so it is not used (Meshtastic leaves it out too) +#define EXT_PWR_DETECT (5) // P0.5 + +#define ADC_RESOLUTION (14) +#define BATTERY_SENSE_RES (12) + +#define AREF_VOLTAGE (3.0) + +//////////////////////////////////////////////////////////////////////////////// +// Number of pins + +#define PINS_COUNT (48) +#define NUM_DIGITAL_PINS (48) +#define NUM_ANALOG_INPUTS (6) +#define NUM_ANALOG_OUTPUTS (0) + +//////////////////////////////////////////////////////////////////////////////// +// UART pin definition + +#define PIN_SERIAL1_RX (14) // P0.14 (GPS) +#define PIN_SERIAL1_TX (13) // P0.13 (GPS) + +#define PIN_SERIAL2_RX (17) // P0.17 +#define PIN_SERIAL2_TX (16) // P0.16 + +//////////////////////////////////////////////////////////////////////////////// +// I2C pin definition + +#define HAS_WIRE (1) +#define WIRE_INTERFACES_COUNT (1) + +#define PIN_WIRE_SDA (47) // P1.15 +#define PIN_WIRE_SCL (46) // P1.14 +#define I2C_NO_RESCAN + +//////////////////////////////////////////////////////////////////////////////// +// SPI pin definition + +#define SPI_INTERFACES_COUNT (1) + +#define PIN_SPI_MISO (40) // P1.8 +#define PIN_SPI_MOSI (41) // P1.9 +#define PIN_SPI_SCK (11) // P0.11 +#define PIN_SPI_NSS (12) // P0.12 + +//////////////////////////////////////////////////////////////////////////////// +// Builtin LEDs (RGB) + +#define LED_BUILTIN (-1) +#define LED_RED (3) // P0.3 +#define LED_GREEN (24) // P0.24 +#define LED_BLUE (28) // P0.28 +#define LED_PIN LED_GREEN + +#define LED_STATE_ON HIGH + +//////////////////////////////////////////////////////////////////////////////// +// Builtin buttons + +#define PIN_BUTTON1 (6) // P0.6, active HIGH (internal pull-down) +#define BUTTON_PIN PIN_BUTTON1 + +//////////////////////////////////////////////////////////////////////////////// +// LR2021 + +#define LORA_DIO_1 (33) // P1.1, IRQ line (LR2021 DIO8) +#define LORA_NSS (PIN_SPI_NSS) // P0.12 +#define LORA_RESET (42) // P1.10 +#define LORA_BUSY (7) // P0.7 +#define LORA_SCLK (PIN_SPI_SCK) // P0.11 +#define LORA_MISO (PIN_SPI_MISO) // P1.8 +#define LORA_MOSI (PIN_SPI_MOSI) // P1.9 + +//////////////////////////////////////////////////////////////////////////////// +// GPS (Airoha, dual-band L1+L5) + +#define HAS_GPS 1 +#define GPS_RX_PIN PIN_SERIAL1_RX +#define GPS_TX_PIN PIN_SERIAL1_TX +#define GPS_BAUD_RATE (115200) + +#define GPS_EN (43) // P1.11, active HIGH +#define GPS_RESET (8) // P0.8, active HIGH + +#define GPS_VRTC_EN (45) // P1.13 +#define GPS_SLEEP_INT (30) // P0.30 +#define GPS_RTC_INT (29) // P0.29 + +//////////////////////////////////////////////////////////////////////////////// +// Haptic driver (DRV2605 on I2C) + +#define PIN_DRV_EN (37) // P1.5, power to haptic driver + +//////////////////////////////////////////////////////////////////////////////// +// Buzzer + +#define BUZZER_PIN (25) // P0.25, pwm output + +//////////////////////////////////////////////////////////////////////////////// +// QSPI Flash + +#define PIN_FLASH_EN (15) // P0.15 (Flash power enable) + +#define PIN_QSPI_SCK (19) // P0.19 +#define PIN_QSPI_CS (20) // P0.20 +#define PIN_QSPI_IO0 (21) // P0.21 +#define PIN_QSPI_IO1 (22) // P0.22 +#define PIN_QSPI_IO2 (23) // P0.23 +#define PIN_QSPI_IO3 (32) // P1.00 + +#define EXTERNAL_FLASH_DEVICES GD25Q64C \ No newline at end of file diff --git a/variants/sensecap_indicator-espnow/platformio.ini b/variants/sensecap_indicator-espnow/platformio.ini index e643d0339..a5952d6e3 100644 --- a/variants/sensecap_indicator-espnow/platformio.ini +++ b/variants/sensecap_indicator-espnow/platformio.ini @@ -33,7 +33,7 @@ lib_deps=${esp32_base.lib_deps} lovyan03/LovyanGFX @ ^1.2.7 [env:SenseCapIndicator-ESPNow_comp_radio_usb] -extends =SenseCapIndicator-ESPNow +extends = SenseCapIndicator-ESPNow build_flags = ${SenseCapIndicator-ESPNow.build_flags} -I examples/companion_radio/ui-new @@ -47,4 +47,4 @@ build_src_filter = ${SenseCapIndicator-ESPNow.build_src_filter} +<../examples/companion_radio/*.cpp> lib_deps = ${SenseCapIndicator-ESPNow.lib_deps} - densaugeo/base64 @ ~1.4.0 \ No newline at end of file + densaugeo/base64 @ ~1.4.0 diff --git a/variants/sensecap_solar/platformio.ini b/variants/sensecap_solar/platformio.ini index 15c21a63b..87c657fcb 100644 --- a/variants/sensecap_solar/platformio.ini +++ b/variants/sensecap_solar/platformio.ini @@ -101,3 +101,8 @@ build_src_filter = ${SenseCap_Solar.build_src_filter} lib_deps = ${SenseCap_Solar.lib_deps} densaugeo/base64 @ ~1.4.0 + +[env:SenseCap_Solar_kiss_modem] +extends = SenseCap_Solar +build_src_filter = ${SenseCap_Solar.build_src_filter} + +<../examples/kiss_modem/> diff --git a/variants/station_g2/platformio.ini b/variants/station_g2/platformio.ini index 15e23321c..38bca3d8b 100644 --- a/variants/station_g2/platformio.ini +++ b/variants/station_g2/platformio.ini @@ -277,7 +277,7 @@ build_flags = -D WIFI_DEBUG_LOGGING=1 -D WIFI_SSID='"myssid"' -D WIFI_PWD='"mypwd"' - -D OFFLINE_QUEUE_SIZE=256 + -D OFFLINE_QUEUE_SIZE=256 ; -D MESH_PACKET_LOGGING=1 ; -D MESH_DEBUG=1 build_src_filter = ${Station_G2.build_src_filter} @@ -290,11 +290,9 @@ lib_deps = [env:Station_G2_kiss_modem] extends = Station_G2 -build_unflags = - -DARDUINO_USB_MODE=0 build_flags = ${Station_G2.build_flags} - -DARDUINO_USB_MODE=1 + -D ARDUINO_USB_MODE=1 build_src_filter = ${Station_G2.build_src_filter} +<../examples/kiss_modem/> diff --git a/variants/thinknode_m6/platformio.ini b/variants/thinknode_m6/platformio.ini index 3606d6a87..ad7e6902c 100644 --- a/variants/thinknode_m6/platformio.ini +++ b/variants/thinknode_m6/platformio.ini @@ -85,7 +85,6 @@ build_flags = -D BLE_DEBUG_LOGGING=1 -D OFFLINE_QUEUE_SIZE=256 -D AUTO_SHUTDOWN_MILLIVOLTS=3300 - -D QSPIFLASH=1 ; -D MESH_PACKET_LOGGING=1 ; -D MESH_DEBUG=1 build_src_filter = ${ThinkNode_M6.build_src_filter} @@ -107,7 +106,6 @@ build_flags = -I examples/companion_radio/ui-new -D MAX_CONTACTS=350 -D MAX_GROUP_CHANNELS=40 - -D QSPIFLASH=1 -D OFFLINE_QUEUE_SIZE=256 -D AUTO_SHUTDOWN_MILLIVOLTS=3300 -D ENABLE_USB_INTERFACE diff --git a/variants/thinknode_m6/variant.cpp b/variants/thinknode_m6/variant.cpp index c88f387db..79930e2d0 100644 --- a/variants/thinknode_m6/variant.cpp +++ b/variants/thinknode_m6/variant.cpp @@ -30,6 +30,8 @@ void initVariant() { digitalWrite(PIN_GPS_STANDBY, HIGH); pinMode(PIN_GPS_EN, OUTPUT); digitalWrite(PIN_GPS_EN, HIGH); - pinMode(PIN_GPS_RESET, OUTPUT); - digitalWrite(PIN_GPS_RESET, HIGH); + // PIN_GPS_RESET (pin 29 / REINIT) is intentionally left floating (input). + // Driving it HIGH holds the L76K silent, so it never streams NMEA and the + // firmware reports "no GPS". Letting it float lets the module run, matching + // the Meshtastic M6 variant. See GPS_RESET (-1) in variant.h. } diff --git a/variants/thinknode_m6/variant.h b/variants/thinknode_m6/variant.h index 70fd65062..0a4025f3b 100644 --- a/variants/thinknode_m6/variant.h +++ b/variants/thinknode_m6/variant.h @@ -102,7 +102,12 @@ #define PIN_GPS_RX (2) #define PIN_GPS_TX (3) #define PIN_GPS_EN (6) // EN -#define PIN_GPS_RESET (29) +#define PIN_GPS_RESET (29) // REINIT - must FLOAT; driving it (esp. HIGH) silences the L76K +// The M6's L76K streams NMEA on its own and must not have its REINIT pin driven. +// Tell the location provider there is no reset pin so it never touches pin 29 +// (driving it HIGH holds the module silent). Matches Meshtastic, which leaves +// this pin as an input. See variant.cpp (pin 29 is intentionally not configured). +#define GPS_RESET (-1) #define PIN_GPS_STANDBY (30) // STANDBY #define PIN_GPS_PPS (31) #define GPS_BAUD_RATE 9600